43
Shoe Fence
ACCESSORY ASSEMBLY
PREPARATION
• Shoe fences and angled shelves must be installed as you are
assembling and installing the correlating shelf tower.
• A shoe fence should be drilled and fastened together with the
shelf before it is installed in the tower. For angled shelving with
the fences, fasten the back screw-in studs first, and then secure
the front screw-in studs, three holes below the back studs.
• Use the Shoe Fence Template to guide your drilling pattern on the
top side of the shelf. The template has hole patterns for shoe fence
posts to install on both 24 in. and 30 in. shelves.
INSTALLATION
1. Place your cammed shelf, face up, on a work surface to drill the
hole pattern. Hold the shoe fence template in place on
the top of the front (edgebanded) of the shelf.
2. Using the Self Center Drill Bit, drill the three holes through the
template appropriate to either the 24 in. or 30 in. shelf width.
3. Position the shoe fence posts over the drilled holes. Use a rubber
mallet to drive the serrated post extensions of the fence into the
holes you just drilled. Be sure to alternate each mallet hammer
swing between each end and middle post so that the post
extensions fit into the drilled holes straight up and down (and so
that you don’t bend the post extensions).
4. Install the shelf in the tower, fastening the back two cam locks,
over the studs at three holes above the height of the front cam
locks and studs. Shelf will rest on front cam locks only.
Do not lock front cam locks. Wipe down shelf.
DESCRIPTION
Shoe fence (for either
24 in. or 30 in. shelves)
PARTS
QTY
1+
Back Panels
Shelving /Towers
Drawers and Doors
Adjustable Shelves
Molding
}
Baskets, Valet Rods,
Tie & Belt Racks, and
other accessories
Islands
Benches
ORDER OF ASSEMBLY
SHOE FE
NC
E
STEP 2:
USE #8-32 x 1inch SCREWS TO ASSEMBLE
STEP 1:
DRILL 5mm HOLES THRU SHELF AS SHOWN. FOR
24, 30, 36in SIZES, DRILL HOLE FOR CENTER POST 3/4in
FROM FRONT EDGE
19mm
(3/4 in)
19 mm
(3/4 in)
Shelf Width
(12, 18, 24, 30, 36in)
19 mm
(3/4 in)
19 mm
(3/4 in)
5 mm
(3/16 in)
Hole Thru.
Shelf Front
Only for 24, 30, 36in
Shelves
LEFT
RIGHT
12" Shelf (CTC 10.5")
18" Shelf (CTC 16.5")
24" Shelf (CTC 22.5")
30" Shelf (CTC 28.5")
36" Shelf (CTC 34.5")
#8-32 x 1inch Screw
Center post mounting
only for 24, 30, 36 shelves
Summary of Contents for MasterSuite
