34
Tower Doors
DOOR & DRAWER ASSEMBLY
INSTALLATION
1. Assemble the tower to which you plan to attach the cabinet doors.
2. In one hand hold the Door/Hamper Template (#05-90051) against
the left or right partition and against the top shelf. With your free
hand, drill your hinge holes, using the 5mm Self Centering Drill Bit,
through the Lucite Template.
(FIG. 1)
3. Repeat Step 2 for the remaining top location. Then, hold the
template against partition and bottom fixed panel to drill bottom
hinge hole locations.
4. Lift up hinge flap. Insert each hinge into set of three (3) holes on
the back of each door. Then, lower hinge flap to tighten and secure
hinge in hole.
(See FIG. 2)
5. Attach the hinge plates to each side partition by fastening the pre-
mounted screws into the holes you drilled in step 2. Ensure the
arrow next to the empty screw hole is pointed towards the door.
(See FIG. 3)
6. For installation of hinges on a single, shared panel and shared
system holes (back to back)
(See front view in FIG. 5)
, you must
remove each mounting plate’s two fastening screws and replace
them with #56514 Hole Sleeves and Mounting Bolts (from each
side), tightening the bolts from each side of the single panel, same
hole into the sleeve.
7. For normal installation of hinges, fasten the hinge to the hinge
plate. To do so, hold the door with hinges attached so that the
hooks on the back of each hinge latch onto the front leading edge
PREPARATION
• Cabinet Tower Doors must be installed with a fixed shelf at both
the top and bottom of the door set.
• Install all shelves first. Allow 18 holes between shelves for 24 in.
door. Allow 28 holes between shelves for 36 in. door. Allow 43
holes between shelves for 55 in. door.
• The distance from the vertical center of the bottom fixed shelf to
the vertical center of the top fixed shelf totals 23-7/8 in. or 36 in.
for short and half-size doors, and 55-7/16 in. for long doors.
• For installation of full length doors, the middle two hinges should
be measured, drilled and mounted after the door is mounted to
the panel with its top and bottom hinges.
DESCRIPTION
Set of Cabinet Tower
Doors
Handles
Machine Screws
Mounting Plates
Hinges
Hole Sleeves &
Mounting Bolts
(#56514)
Door/Hamper
Template (#05-90051)
Door Handle Template
(#05-90050)
Self Center Drill Bit
(#05-11619)
PARTS
QTY
1
2
4
4
4
Optional
Back Panels
Shelving /Towers
}
Drawers and Doors
Adjustable Shelves
Molding
Baskets, Valet Rods,
Tie & Belt Racks, and
other accessories
Islands
Benches
ORDER OF ASSEMBLY
Summary of Contents for MasterSuite
