7
Stand Alone Tower
PREPARATION
Screw-In Studs or Double-Sided Studs?
Use screw-in studs only in partitions positioned on the end or in
corners. For stand-alone towers, screw-in-studs will typically be used.
Thread screw-in studs into partition holes until the stop ring is snug
with the partition face.
Use double-sided studs for contiguous closet sections in which you
need to have two fixed shelves fastened to either side of the same
system hole. For example, you must use double-sided studs for
neighboring fixed shelves of adjacent double hang sections. For Tower
System or Hanging System, a mix of screw-in studs and double-sided
studs may be used.
1. Lay down both tower side panels (partitions) face up on the
cardboard or cloth with the notched ends at the bottom facing in.
(See FIG. 1)
Use a screwdriver to thread six (6) screw-in studs into
each side panel. Two (2) screw-in-studs will go into top holes, two
(2) screw-in-studs will go into holes located 43 in. down from top,
and two (2) screw-in studs will be above the baseboard notch (5th
hole from the bottom of the panel).
NOTE:
Depending upon the design, the use of screw-in-studs may be
interchangeable with double-sided studs for contiguous sections or adjacent
towers. Use appropriate fastener for the design.
2. Align dowels in one end of cleat with holes in top of left panel as
shown. Push cleat dowels into holes.
(See FIG. 2)
NOTE:
For towers with drawers or baskets, it is optional to fasten the
slide runners on each of the side panel either before full assembly, lying on
the floor, or after standing up the tower. (See “Drawer” in “DRAWER AND
DOOR ASSEMBLY” section for detailed instructions on runner location and
installation.)
3. Turn panel over onto its back edge. Use one (1) HiLow Screw
through hole in side panel.
(See FIG. 3A)
Line up two of the cam
locks of the top fixed shelf over the screw-in studs and push down
over the cams to fasten. Tighten the joint by turning each of the
cam locks a full 180˚ clockwise with a Phillips head screwdriver.
(See FIG. 3B)
Next, fasten the bottom fixed shelf.
(See FIG. 3C)
Finally, attach the middle fixed shelf.
(See FIG. 3D)
SHELVING/TOWER ASSEMBLY
Back Panels
}
Shelving /Towers
Drawers and Doors
Adjustable Shelves
Molding
Baskets, Valet Rods,
Tie & Belt Racks, and
other accessories
Islands
Benches
ORDER OF ASSEMBLY
INSTALLATION
Upright Partitions
Cleat/Toekick
Cam Fixed Shelves
Screw in Studs or Double-Sided
Studs
#8 x 1-1/4 in. Screws
#8 x 5/8 in. Screws
HiLow Screws
Angle (Corner) Brackets
Easy Anchors
Fast Caps
Assorted closet components
(adj. and fixed cam shelves, etc.)
PARTS
Summary of Contents for MasterSuite
