48
Island
ACCESSORY ASSEMBLY
PREPARATION
These instructions apply to assembly of either 1/2 or full island kits.
Each 1/2 island has two facing sides. A full island will have two (2) 1/2
islands connected to make a four facing sided island.
Island units can have many designs, including configurations for
shelves, added doors, drawers and baskets. The basic components’
kit consists of the smooth-finished side panels, divider, shelves, and
toe-kicks. Heavy-duty countertop is sold separately and is available in
either a 1/2 island size of a full island size.
In addition, you must supply the custom design components:
adjustable shelves, doors, drawers and baskets to meet the
customer’s needs.
LOCATION:
As shown in Fig. 1, the basic island, Full (2—25-1/2 in.
sections wide) or Half (1—25-1/2 in. section wide) must b e positioned
in the closet or pantry with a minimum of 24 in. walking space on all
sides. More is better!
Islands with drawers or baskets require 30 in. or more of space
between the island and hanging to accommodate the pull-out
distance of the drawers or baskets. Use the dimensions at right as
a minimum guide.
DESCRIPTION
Island Kit (2 sides, 1
divider, 4 cam
shelves -for top and
bottom, and 2
toe kicks for each 1/2
island)
Screw-in Studs #56544
(for each half island)
#4.5 X 32mm Screws
PARTS
QTY
1+
30
4
INSTALLATION
1. With both side panels positioned with holes facing up, thread
eight (8) screw-in studs into the pre-drilled holes across the top
and bottom of each panel as shown.
(See FIG. 1a)
NOTE:
Thread all screw-in studs into holes until the stop ring is snug with
the partition face.
Thread three (3) screw-in studs into each panel down along
the three middle holes as shown.
(See FIG. 1b)
Thread four (4)
screw-in studs into each side panel at toe kick location holes.
(See FIG. 1c)
For optional drawer(s) assembly:
Fasten drawer runners (using
2 Euro screws each - provided with the drawer assembly) to any
remaining pre-drilled holes on both side panels.
2. Place divider on side panel (along center screw-in studs) and
push cam locks over
screw-in studs.
(See FIG. 2)
Use a Phillips screwdriver to tighten
all cam locks at stud location.
(See FIG. 3)
Back Panels
Shelving /Towers
Drawers and Doors
Top Shelves and Poles
Adjustable Shelves
Molding
Baskets, Valet Rods,
Tie & Belt Racks, and
other accessories
}
Islands
Benches
ORDER OF ASSEMBLY
Summary of Contents for MasterSuite
