37
Molding
ACCESSORY ASSEMBLY
INSTALLATION
2. Mark your first measurement. For example, begin left to right in installation of
(FIG. 3)
, using the shelf depth
as your first cut to mark. From the 90° end cut of the panel, mark the distance 14 in. on the back of the molding
(in the groove for crown molding –
(FIG. 5)
The groove is aligned directly over the front edge of the top shelf for
crown molding.
3. Your first cut is the 14 in. length, with the 45° angle at “A” in
(FIG 2)
. Position your molding panel against the
saw guard rail, carefully aligning your mark in the groove with the blade and preset notching for a 45° angle miter
cut.
4. Next, measure and cut the front molding piece going from corner “A” to cut “B.” Since the first piece you just cut
left you with a 45° “inside right” angle end, you will have to trim it off to make an “outside left” 45° miter cut with
which to start the measuring from “A” to “B.”
(FIG. 4)
is an example of how an 8-foot length of molding can be cut
to make the molding pieces for
(FIG. 2 and 3)
, working from left to right.
5. Change the saw preset angle to 22.5 in., as in the second “B” marking in
(FIG. 4)
. Check your blade alignment to
the mark in the groove. Make your cut. Check your blade alignment to the mark in the groove. Make
your cut.
6. Test your first two molding pieces in place. Ensure each length and cut fits EXACTLY to each corner. If either is
too short, cut a new piece. If one is too long, trim to fit.
INSTALL CROWN MOLDING
1. Using your glue gun with the two pieces held closely together on a flat surface, apply the hot glue to joint and
squeeze the two pieces together for a tight, perfect match. Glue will set in 10 seconds or less.
2. Carefully holding your glued, L-shaped molding configuration in hand, position the pieces in place on top of the
tower/shelving. The abutted pieces should keep them standing up straight and not tip forward over
the edge.
3. Predrill each screw location to fasten molding to tower/shelving. Screw in the molding through pre-drilled
holes in each corner and along the length where needed (approx. every 12 in. - 14 in.), using #8 x 1-1/4 in. screw.
(FIG. 6)
4. Repeat measuring, marking, cutting, testing, gluing and fastening steps for each section of crown molding to
install. Always try to put up two (or three) glued pieces at a time for stability.
5. To further secure crown molding, install crown molding braces on any diagonal joints using a screw.
(FIG. 7)
6. Repeat measuring, marking, cutting, testing, and fastening steps for each section of crown molding to install.
Summary of Contents for MasterSuite
