Cisco UCS C210 Installation And Service Manual Download Page 93

Page: 93 / 124

C-1

Cisco UCS C210 Server Installation and Service Guide

OL-20887-02

A P P E N D I X

RAID Controller Considerations

This appendix contains the following sections:

•

Supported RAID Controllers and Required Cables, page C-1

•

Enabling the Integrated Intel ICH10R RAID Controller in the BIOS, page C-2

•

Enabling the Mezzanine Card RAID Controller in the BIOS, page C-3

•

RAID Controller Cabling, page C-3

•

How to Determine Which Controller Is in Your Server, page C-4

•

How to Disable Quiet Boot for CIMC Firmware Earlier Than Release 1.2(1), page C-5

•

How To Launch Option ROM-Based Controller Utilities, page C-5

•

LSI MegaRAID Card Beep Codes, page C-6

•

Restoring RAID Configuration After Replacing a RAID Controller, page C-6

•

For More Information, page C-7

Supported RAID Controllers and Required Cables

This server supports the RAID controller options and cable requirements shown in

Table C-1

Note

This server contains a default drive backplane called an

extender

, which supports controller connection

for up to 8 drives. To control more than 8 drives (maximum 16), the server must be ordered with the
optional

expander

backplane. The extender/expander backplanes are not field-upgradeable.

Note

Different cables might be required when connecting to the extender versus the expander, as described in

Table C-1

Note

Do not mix controller types in the server. Dual controllers are not supported.

Summary of Contents for UCS C210





























































































































Search results

Summary of Contents for UCS C210

Reviews:

Related manuals for UCS C210

Brands by name

Popular brands

Cisco UCS C210, Installation And Service Manual

Search results

Summary of Contents for UCS C210

Reviews:

Related manuals for UCS C210

Brands by name

Popular brands