Cisco UCS C210 Installation And Service Manual Download Page 50

Page: 50 / 124

3-12

Cisco UCS C210 Server Installation and Service Guide

OL-20887-02

Chapter

Replaceable Component Locations

This section shows the locations of the components that are discussed in this chapter. The view in

Figure 3-5

is from the top down, with the top cover and internal air baffle removed.

Figure 3-5

Replaceable Component Locations (top view)

Hard drives (up to 16, accessible through front
bays)

DVD drive

Fan tray

DIMM slots (up to 12)

CPUs and heatsinks (up to two)

CMOS battery

PCIe card slot for riser card (with chassis
openings for three standard-profile cards)

Riser card assembly

PCIe card slot for riser card (with chassis
openings for two standard-profile cards)

Socket for trusted platform module (TPM)

Socket for LSI mezzanine card

Power supplies (up to two, accessible through
rear bays)

Internal USB port on motherboard



(active in server Generation M2 only)

195918

Summary of Contents for UCS C210





























































































































Search results

Summary of Contents for UCS C210

Reviews:

Related manuals for UCS C210

Brands by name

Popular brands

Cisco UCS C210, Installation And Service Manual

Search results

Summary of Contents for UCS C210

Reviews:

Related manuals for UCS C210

Brands by name

Popular brands