Cisco UCS C210 Installation And Service Manual Download Page 32

Page: 32 / 124

2-14

Cisco UCS C210 Server Installation and Service Guide

OL-20887-02

Chapter

Accessing the System BIOS

You can change the BIOS settings for your server by using the procedure in this section. Detailed
instructions are also printed on the BIOS screens.

Step 1

Enter the BIOS setup utility by pressing the

key when prompted during bootup.

Note

The version and build of the current BIOS are displayed on the Main page of the utility.

Step 2

Use the arrow keys to select the BIOS menu page.

Step 3

Highlight the field to be modified by using the arrow keys.

Step 4

Press

Enter

to select the field that you want to change, and then modify the value in the field.

Step 5

Press the right arrow key until the Exit menu screen is displayed.

Step 6

Follow the instructions on the Exit menu screen to save your changes and exit the setup utility (or Press

F10

). You can exit without saving changes by pressing

Esc

Summary of Contents for UCS C210





























































































































Search results

Summary of Contents for UCS C210

Reviews:

Related manuals for UCS C210

Brands by name

Popular brands

Cisco UCS C210, Installation And Service Manual

Search results

Summary of Contents for UCS C210

Reviews:

Related manuals for UCS C210

Brands by name

Popular brands