Cisco PA-2CT1 Installation And Configuration Manual Download | Manualshive

Page: 49 / 54

background image

Channelized T1 Port Adapter Installation and Configuration 49

Configuring 2CT1 Interfaces

The following example of the show interfaces serial port adapter slot number/interface port
number:pri-group command shows all of the information specific to the same interface (interface
port 1 in port adapter slot 1) when the interface is configured for ISDN PRI:

Router# show interface serial 1/1:23

Serial1/1:23 is up, line protocol is up (spoofing)

Hardware is MPA-T1

Internet address is 10.1.15.1

MTU 1500 bytes, BW 1984 Kbit, DLY 20000 usec, rely 255/255, load 1/255

Encapsulation HDLC, loopback not set

Last input 00:00:42, output 00:00:56, output hang never

Last clearing of “show interface” counters never

Input queue: 0/75/0 (size/max/drops); Total output drops: 0

Queueing strategy: weighted fair

Output queue: 0/64/0 (size/threshold/drops)

Conversations 0/1 (active/max active)

Reserved Conversations 0/0 (allocated/max allocated)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

149 packets input, 40207 bytes, 0 no buffer

Received 298 broadcasts, 0 runts, 0 giants

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

128 packets output, 44416 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

20 carrier transitions no alarm present

Timeslot(s) Used:1-24, subrate: 64Kb/s, transmit delay is 0 flags

Note

In the above example, the term “spoofing” indicates that the interface is configured for ISDN

PRI. The term ”spoofing” is indicated only on timeslot 24 (the D channel), which is recognized by
the system as timeslot 23.

Use the show controllers t1 [port adapter slot number/interface port number] command to display
the status of each installed T1 interface. The following example of the show controllers t1
command shows the status of a 2CT1 port adapter installed in port adapter slot 1, interface port 0:

Router# show controllers t1 1/0

T1 1/0 is up.

No alarms detected.

Framing is ESF, Line Code is B8ZS, Clock Source is Line.

Data in current interval (710 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Data in Interval 1:

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

[display text omitted]

«
...
47
48
49
50
51
...
»

Summary of Contents for PA-2CT1























































Reviews:

No comments

Related manuals for PA-2CT1

Brand: Patton electronics Pages: 6

Brand: Hainbuch Pages: 68

Brand: StarTech.com Pages: 13

Bluetooth USB-Adapter Version 1.2

Brand: Hama Pages: 8

Brand: Emulex Pages: 2

Brand: NI Pages: 11

Brand: Future Domain Pages: 48

Brand: S2Konnect Pages: 26

Brand: PureLink Pages: 16

ALMEMO 8006-RTA3

Brand: Ahlborn Pages: 16

Brand: Dynex Pages: 20

Brand: Salto Pages: 2

Brand: Asante Pages: 26

Brand: Sony Pages: 2

VAIO VGP-AC19V12

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

TDM-iP50 - Digital Media Port Cradle

Brand: Sony Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands