Cisco PA-2CT1 Installation And Configuration Manual Download | Manualshive

Page: 38 / 54

background image

38 Channelized T1 Port Adapter Installation and Configuration

Cisco 7200 Series and the 2CT1 Port Adapter

When you enter the correct password, the system displays the privileged-level system
prompt (#):

Router#

Proceed to the following section to configure the new interfaces.

Configuring 2CT1 Interfaces

If you installed a new 2CT1 or if you want to change the configuration of an existing interface, you
must use the privileged-level configure command. If you replaced a 2CT1 port adapter that was
previously configured, the system will recognize the new 2CT1 port adapter interfaces and bring
each of them up in their existing configuration.

After you verify that the new 2CT1 port adapter is installed correctly (the enabled LED goes on),
use the configure command to configure the new interfaces. Be prepared with the information you
will need, such as the following:

•

ISDN switch type, when configuring ISDN PRI ( lists ISDN service provider
switch types)

•

T1 information, for example, clock source, line code, framing type, and so on

•

Channel group and PRI group information and timeslot mapping

•

Protocols and encapsulations you plan to use on the new interfaces

•

Protocol specific information, such as IP addresses, if you plan to configure the interfaces for IP
routing

•

Whether the new interface will use bridging

Note

Configuration commands are executed from the privileged level of the EXEC command

interpreter, which usually requires password access. See the previous section “Using the EXEC
Command Interpreter” and contact your system administrator, if necessary, to obtain access.

Table 6

ISDN Service Provider Switch Types

Keywords by Area

Switch Type

Australia

basic-ts013

Australian TS013 switches

Europe

basic-1tr6
basic-nwnet3
basic-net3

basic-net5
primary-net5
vn2
vn3

German 1TR6 ISDN switches
Norwegian NET3 ISDN switches (phase 1)
NET3 ISDN switches (UK, Denmark, and other nations);

covers the Euro-ISDN E-DSSI signaling system)

NET5 switches (UK and Europe)
European ISDN PRI switches (UK and Europe)
French VN2 ISDN switches
French VN3 ISDN switches

Japan

ntt
primary-ntt

Japanese NTT ISDN switches
Japanese ISDN PRI switches

«
...
36
37
38
39
40
...
»

Summary of Contents for PA-2CT1























































Reviews:

No comments

Related manuals for PA-2CT1

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 12

BLPA100KTA - HD-PLC ETHERNET ADAPT.2PK

Brand: Panasonic Pages: 2

Brand: KAT VR Pages: 2

Brand: I-GO Pages: 2

Avaya one-X Gigabit Ethernet Adapter

Brand: Avaya Pages: 40

Brand: NEC Pages: 7

Versa WiFi USB Adapter 3

Brand: C. Crane Pages: 30

Brand: Linksys Pages: 343

Brand: Adaptec Pages: 8

Brand: Toto Link Pages: 1

Brand: Synapse Pages: 33

Brand: AR Pages: 20

Brand: DeLOCK Pages: 8

USB VGA Display Adapter

Brand: J5create Pages: 48

Brand: National Instruments Pages: 52

Brand: ISY Pages: 20

Brand: J-Tech Digital Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands