manualshive.com logo in svg

Cisco PA-2CT1, Installation And Configuration Manual

Share
Download
Cisco PA-2CT1 Installation And Configuration Manual Download Page 31

Channelized T1 Port Adapter Installation and Configuration  31

Configuring 2CT1 Interfaces

        Controller Memory Size: 8 MBytes

        PA Bay 0 Information:

                Token Ring PA, 4 ports

                EEPROM format version 1

                HW rev 1.0, Board revision B0

                Serial number: 02825610  Part number: 73-1390-04

        PA Bay 1 Information:

Multi-channel (T1) port adapter, 2 ports

                EEPROM format version 255

                HW rev FF.FF, Board revision UNKNOWN

                Serial number: 4294967295  Part number: 255-65535-255

Use the show controllers cbus [type slot/port adapter/interface] command to display the internal
status of each installed interface processor and VIP2, including slot locations, hardware versions,
and the currently running microcode versions. The show controllers cbus command also lists each
interface (port), including logical interface numbers, interface types, physical (slot/port) addresses,
and hardware (station address) of each interface, and cable types attached to each interface.

The following example shows a 2CT1 port adapter installed in chassis slot 3:

Router# show controllers cbus

slot3: VIP2, hw 2.2, sw 21.40, ccb 5800FFA0, cmdq 480000C0, vps 8192

    software loaded from flash slot0:muck/amcrae/vip2_21-40.mxt

    FLASH ROM version 255.255

T1 3/1/1, applique is Channelized T1

gfreeq 48000138, lfreeq 48000180 (1536 bytes), throttled 0

rxlo 4, rxhi 99, rxcurr 0, maxrxcurr 0

[display text omitted]

Use the show controllers t1 command to display the status of each installed T1 interface. The
following example shows the status of a 2CT1 port adapter installed in chassis slot 3 port adapter
slot 1 interface port 0:

Router# show controller t1

T1 3/1/0 is up.

  No alarms detected.

  Framing is ESF, Line Code is B8ZS, Clock Source is Line.

  Data in current interval (700 seconds elapsed):

     0 Line Code Violations, 0 Path Code Violations

     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

  Data in Interval 1:

     10 Line Code Violations, 1 Path Code Violations

     0 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins

     1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 1 Unavail Secs

  Total Data (last 1 15 minute intervals):

     10 Line Code Violations, 1 Path Code Violations,

     0 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins,

     1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 1 Unavail Secs

T1 3/1/1 is up.

  No alarms detected.

  Framing is ESF, Line Code is B8ZS, Clock Source is Line.

  Data in current interval (700 seconds elapsed):

     0 Line Code Violations, 0 Path Code Violations

     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

  Data in Interval 1:

     10 Line Code Violations, 1 Path Code Violations

     0 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins

     1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 1 Unavail Secs

Summary of Contents for PA-2CT1























































Reviews:

No comments

Brands by name

Popular brands

Load more brands