manualshive.com logo in svg

Cisco PA-2CT1, Installation And Configuration Manual

Share
Download
Cisco PA-2CT1 Installation And Configuration Manual Download Page 48

48 Channelized T1 Port Adapter Installation and Configuration

Cisco 7200 Series and the 2CT1 Port Adapter

Step 3

Specify one of the new T1 interfaces with the show interfaces type port adapter
slot/interface port number:channel-group or pri-group command and verify that the first
line of the display specifies the interface with the correct slot number. Also verify that the
interface and line protocol are in the correct state: up or down.

Step 4

Display the protocols configured for the entire system and specific interfaces with the
show protocols command. If necessary, return to configuration mode to add or remove
protocol routing on the system or specific interfaces.

Step 5

Display the running configuration file with the show running-config command. Display
the configuration stored in NVRAM using the show startup-config command. Verify
that the configuration is accurate for the system and each interface.

If the interface is down and you configured it as up, or if the displays indicate that the hardware is
not functioning properly, ensure that the network interface is properly connected and terminated. If
you still have problems bringing up the interface, contact a customer service representative for
assistance.

To display information about a specific interface, use the show interfaces command with the
interface type, port adapter slot, interface port, and channel-group or PRI group address in the format
show interfaces [type port adapter slot/interface port:channel-group or pri-group].

The following example of the show interfaces serial port adapter slot number/interface port
number:channel-group command shows all of the information specific to the second 2CT1 interface
port (interface port 1) in port adapter slot 1, channel group 2:

Router# show interface serial 1/0:2

Serial1/1:2 is up, line protocol is up

  Hardware is MPA-T1

  Internet address is 10.1.15.1

  MTU 1500 bytes, BW 1984 Kbit, DLY 20000 usec, rely 255/255, load 1/255

  Encapsulation HDLC, loopback not set

  Last input 00:00:42, output 00:00:56, output hang never

  Last clearing of “show interface” counters never

  Input queue: 0/75/0 (size/max/drops); Total output drops: 0

  Queueing strategy: weighted fair

  Output queue: 0/64/0 (size/threshold/drops)

     Conversations  0/1 (active/max active)

     Reserved Conversations 0/0 (allocated/max allocated)

  5 minute input rate 0 bits/sec, 0 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

     149 packets input, 40207 bytes, 0 no buffer

     Received 298 broadcasts, 0 runts, 0 giants

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

     128 packets output, 44416 bytes, 0 underruns

     0 output errors, 0 collisions, 0 interface resets

     0 output buffer failures, 0 output buffers swapped out

     20 carrier transitions no alarm present

  Timeslot(s) Used:1-24, subrate: 64Kb/s, transmit delay is 0 flags

Summary of Contents for PA-2CT1























































Reviews:

No comments

Brands by name

Popular brands

Load more brands