Cisco PA-2CT1 Installation And Configuration Manual Download | Manualshive

Page: 26 / 54

background image

26 Channelized T1 Port Adapter Installation and Configuration

VIP2 and the 2CT1 Port Adapter

Step 3

Specify the controller to configure by entering the command controller, followed by t1,
and chassis slot number/port adapter number/interface port number. The example that
follows is for the 2CT1 in chassis slot 3, port adapter slot 1, interface port 1:

Router(config)# cont t1 3/1/1

Step 4

Specify the controller’s clock source by entering the clock source command as follows:

Router(config-controller)# clock source line

Note

You can set the clock source to use internal clocking for testing purposes. One end

of a T1 circuit must provide the clock source.

Step 5

Specify the controller’s framing type by entering the framing command as follows:

Router(config-controller)# framing esf

Step 6

Specify the controller’s linecode format by entering the linecode command as follows:

Router(config-controller)# linecode b8zs

Step 7

Map timeslots to the controller’s PRI group by entering the pri-group command. The
following example shows PRI-group timeslots 1, 3 through 5, and 7 (the B channels)
selected and mapped to timeslot 24 (the D channel), which is recognized by the system
as timeslot 23:

Router(config-controller)# pri-group timeslots 1,3-5,7

Router(config-controller)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/1/1:23,

changed state to down

%LINK-3-UPDOWN: Interface Serial3/1/1:23, changed state to up

Note

In the above example, the line-protocol status for timeslot 24 (listed in the output

as timeslot 23) represents the entire PRI group.

Step 8

If IP routing is enabled on the system, assign an IP address and subnet mask to the PRI
group with the interface and ip address commands as follows.

Note

For channelized T1 ISDN PRI, the PRI group is configured by using timeslot 24,

which is recognized by the system as timeslot 23.

Router(config-controller)# interface serial 3/1/1:23

Router(config-if)# ip address 10.1.15.1 255.255.255.0

Router(config-if)#

Step 9

Add any additional configuration commands required to enable routing protocols and
adjust the interface characteristics.

«
...
24
25
26
27
28
...
»

Summary of Contents for PA-2CT1























































Reviews:

No comments

Related manuals for PA-2CT1

Brand: Panasonic Pages: 8

Brand: 3idee Pages: 7

Brand: TEXIO Pages: 49

Brand: C2G Pages: 24

Brand: Arctic Pages: 25

NWD-210N - V1.0

Brand: ZyXEL Communications Pages: 152

Brand: StarTech.com Pages: 2

Brand: Hamlet Pages: 5

NetBlaster ZX345

Brand: ZNYX Pages: 12

Brand: Bebob Pages: 3

AirPlus DWL-810+

Brand: D-Link Pages: 29

Brand: D-Link Pages: 16

AirPlus DWL-G120

Brand: D-Link Pages: 40

AirPlus DWL-650+

Brand: D-Link Pages: 62

AirPlus G DI-524

Brand: D-Link Pages: 12

AirPlus DWL-810

Brand: D-Link Pages: 2

802.11g Wireless LAN USB Adapter DWL-G122

Brand: D-Link Pages: 56

AirPlus DWL-650+

Brand: D-Link Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands