Cisco PA-2CT1 Installation And Configuration Manual Download

Page: 10 / 54

10 Channelized T1 Port Adapter Installation and Configuration

What Is the 2CT1 Port Adapter?

Figure 4

Cisco 7200 Series Port Adapters (Cisco 7206 Shown)

2CT1 Port Adapter LEDs

The 2CT1 port adapter has an enabled LED, standard on all port adapters, and three status LEDs for
each port. (See Figure 5.)

Figure 5

LEDs on the 2CT1 Port Adapter (Horizontal Orientation Shown)

After system initialization, the enabled LED goes on to indicate that the port adapter has been
enabled for operation.

The following conditions must be met before the 2CT1 port adapter is enabled:

•

The port adapter is correctly connected to the backplane or midplane and receiving power.

•

A valid system software image for the port adapter has been downloaded successfully.

•

The system software recognizes the port adapter or 2CT1-equipped VIP2.

If any of the above conditions are not met, or if the initialization fails for other reasons, the enabled
LED will not go on. Table 2 lists port LED status indications.

H6422

ETHERNET 10BT

ENABLED

LINK

ENABLED

MII

LINK

RJ45

FAST ETHERNET

Port adapter slot 5

Port adapter slot 3

Port adapter slot 1

FAST SERIAL

LB CD

TOKEN RING

ETHERNET-10BFL

Blank port adapter

Port adapter slot 6

Port adapter slot 4

Port adapter slot 2

MII

RJ45

LINK

1O PWR

RJ-45

CPU RESET

FAST ETHERNET INPUT/OUTPUT CONTROLLER

ENABLED

PCMCIA

EJECT

SLOT 0

SLOT 1

FE MII

Port adapter slot 0

H8659

Summary of Contents for PA-2CT1























































Search results

Summary of Contents for PA-2CT1

Reviews:

Related manuals for PA-2CT1

Brands by name

Popular brands

Cisco PA-2CT1, Installation And Configuration Manual

Search results

Summary of Contents for PA-2CT1

Reviews:

Related manuals for PA-2CT1

Brands by name

Popular brands