Cisco PA-2CT1 Installation And Configuration Manual Download | Manualshive

Page: 2 / 54

background image

2 Channelized T1 Port Adapter Installation and Configuration

Related Documentation

Related Documentation

Your router and the Cisco IOS software running on it contain extensive features and functionality,
which are documented in the following resources:

•

For Cisco IOS software configuration information and support, refer to the modular
configuration and modular command reference publications in the Cisco IOS software
configuration documentation set that corresponds to the software release installed on your Cisco
hardware.

Note

You can access Cisco IOS software configuration and hardware installation and

maintenance documentation on the World Wide Web at http://www.cisco.com,
http://www-china.cisco.com, or http://www-europe.cisco.com.

•

For hardware installation and maintenance information on Cisco 7200 routers, refer to the
Cisco 7200 Series Installation and Configuration Guide that shipped with your
Cisco 7200 series router.

•

For hardware installation and maintenance information on Cisco 7200 VXR routers, refer to the
Cisco 7200 VXR Installation and Configuration Guide publication that shipped with your
Cisco 7200 VXR router.

•

For port adapter hardware and memory configuration guidelines for Cisco 7200 series routers,
refer to the document Cisco 7200 Series Port Adapter Hardware Configuration Guidelines.

•

For international agency compliance, safety, and statutory information for interfaces for
Cisco 7000 series routers, Cisco 7200 series routers, and Cisco 7500 series routers, refer to the
following publications:

— Regulatory Compliance and Safety Information for the Cisco 7500 Series Routers

— Regulatory Compliance and Safety Information for the Cisco 7000 Series Routers

— Regulatory Compliance and Safety Information for the Cisco 7200 Series Routers

•

For hardware installation and maintenance information on Cisco 7000 series and Cisco 7500
series routers, and the VIP2, refer to the following publications:

— The installation and configuration guide that shipped with your Cisco 7000 series or

Cisco 7500 series router

— Second-Generation Versatile Interface Processor (VIP2) Installation and Configuration (for

VIP2 users only)

To view Cisco documentation or obtain general information about the documentation, see the “Cisco
Connection Online” section on page 52, the “Documentation CD-ROM” section on page 53, or call
Customer Service at 800 553-6387 or 408 526-7208. Customer Service hours are 5:00 a.m. to 6:00
p.m. Pacific time, Monday through Friday (excluding company holidays). You can also send e-mail
to [email protected], refer to the Cisco Information Packet that shipped with your router.

«
1
2
3
4
...
»

Summary of Contents for PA-2CT1























































Reviews:

No comments

Related manuals for PA-2CT1

D DPH-50U DPH-50U

Brand: D-Link Pages: 2

AirPlus DWL-810

Brand: D-Link Pages: 64

Brand: D-Link Pages: 39

Brand: D-Link Pages: 8

802.11g Wireless LAN USB Adapter DWL-G122

Brand: D-Link Pages: 43

AirPlusXtremeG DWL-G650

Brand: D-Link Pages: 20

SmartSwitch 6C110

Brand: Cabletron Systems Pages: 7

Brand: cable matters Pages: 52

Brand: TRENDnet Pages: 21

Brand: Parani Pages: 48

Brand: P+S Technik Pages: 2

Brand: TP-Link Pages: 33

Brand: TAPaulk Communications Pages: 3

Brand: Actron Pages: 2

Brand: Leader Pages: 12

Brand: Aiphone Pages: 2

1130U2 - Storage Controller RAID)- U2W SCSI 80 MBps

Brand: Adaptec Pages: 82

USB ADAPTER PLUS

Brand: KROHNE Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands