Cisco PA-2CT1 Installation And Configuration Manual Download | Manualshive

Page: 1 / 54

background image

1

Cisco Systems, Inc.
All rights reserved.

170 West Tasman Drive
San Jose, CA 95134-1706
USA

Cisco Systems, Inc.

Corporate Headquarters

Copyright © 1996–1999

Text Part Number:

Channelized T1 Port Adapter Installation
and Configuration

Product Number: PA-2CT1/PRI(=)

This configuration note describes how to install and configure the channelized T1 Integrated
Services Digital Network (ISDN) Primary Rate Interface (PRI) port adapter (PA-2CT1/PRI),
hereafter referred to as the 2CT1 port adapter, in the following platforms:

•

Cisco 7200 series routers—which consist of the two-slot Cisco 7202, the four-slot Cisco 7204
and Cisco 7204VXR, and the six-slot Cisco 7206 and Cisco 7206VXR

•

Second-generation Versatile Interface Processor (VIP2) in all Cisco 7000 series routers and
Cisco 7500 series routers using the 7000 Series Route Switch Processor (RSP7000) and
7000 Series Chassis Interface (RSP7000CI) installed

Document Contents

This configuration note is organized into three parts:

1

The following sections include general information and information about port adapter
installation:

— Related Documentation, page 2

— Port Adapter Installation Prerequisites, page 3

2

The following section includes information specific to the 2CT1 port adapter:

— What Is the 2CT1 Port Adapter?, page 7

3

The following sections include information specific to the 2CT1 port adapter’s use on the VIP2
in Cisco 7500 series routers and in Cisco 7000 series routers using the RSP7000 and RSP7000CI,
and in Cisco 7200 series routers:

— VIP2 and the 2CT1 Port Adapter, page 12

— Cisco 7200 Series and the 2CT1 Port Adapter, page 33

The “Cisco Connection Online” section on page 52 includes general reference information.

78-3940-05

1
2
3
...
»

Summary of Contents for PA-2CT1























































Reviews:

No comments

Related manuals for PA-2CT1

Brand: Conrad Pages: 4

Brand: Origaudio Pages: 1

Brand: G-cluster Pages: 2

Brand: Gemtek Systems Pages: 20

HandyTone-286 Rev 3.0

Brand: Grandstream Networks Pages: 12

Brand: Agilent Technologies Pages: 32

Brand: KTI Pages: 25

Brand: Lindy Pages: 2

Brand: Yealink Pages: 8

Brand: IBM Pages: 60

Brand: TP-Link Pages: 32

Brand: Westermo Pages: 28

Brand: i-tec Pages: 20

Brand: Sony Pages: 2

PCWA-C800S Read This First

Brand: Sony Pages: 1

Brand: Sony Pages: 2

Brand: Sony Pages: 4

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands