manualshive.com logo in svg

Cisco PA-2CT1, Installation And Configuration Manual

Share
Download
Cisco PA-2CT1 Installation And Configuration Manual Download Page 34

34 Channelized T1 Port Adapter Installation and Configuration

Cisco 7200 Series and the 2CT1 Port Adapter

When a port adapter slot is not in use, a blank port adapter must fill the empty slot to allow the router
to conform to EMI emissions requirements and to allow proper air flow across the port adapters. If
you plan to install a new port adapter in a slot that is not in use, you must first remove a blank port
adapter.

Removing a Port Adapter

Use the following procedure to remove a port adapter from a Cisco 7200 series router:

Step 1

Attach an ESD-preventative wrist strap between you and an unfinished chassis surface.

Step 2

Place the port adapter lever for the desired port adapter slot in the unlocked position. The
port adapter lever remains in the unlocked position. (See Figure 16.)

Figure 16

Placing the Port Adapter Lever in the Unlocked Position (Cisco 7206 Shown)

Step 3

Grasp the handle on the port adapter and pull the port adapter from the midplane, about
halfway out of its slot. If you are removing a blank port adapter, pull the blank port
adapter completely out of the chassis slot.

Note

As you disengage the port adapter from the router midplane, OIR administratively

shuts down all active interfaces on the port adapter.

Step 4

With the port adapter halfway out of the slot, disconnect all cables from the port adapter.

Step 5

After disconnecting the cables, pull the port adapter from its chassis slot.

Caution

Always handle the port adapter by the carrier edges and handle; never touch the port

adapter’s components or connector pins. (See Figure 17.)

ETHERNET 10BT

ENABLED

0

2

1

3

LINK

0

1

2

3

FAST SERIAL

EN

TD

TC

RD

RC

LB CD

TD

TC

RD

RC

LB CD

TD

TC

RD

RC

LB CD

TD

TC

RD

RC

LB CD

ENABLED

MII

LINK

RJ45

FAST ETHERNET 

0

TOKEN RING

0

1

2

3

0

2

4

1

3

5

6

H6596

MII

EN

RJ45

EN

RJ45

LINK

1O PWR

OK

RJ-45

CPU RESET

FAST ETHERNET INPUT/OUTPUT CONTROLLER

ENABLED

PCMCIA

EJECT

SLOT 0

SLOT 1

FE MII

Port adapter

handle

Port adapter

lever (unlocked

position)

Note: This adapter removal
applies to any port or service
adapter.

Summary of Contents for PA-2CT1























































Reviews:

No comments

Brands by name

Popular brands

Load more brands