Cisco PA-2CT1 Installation And Configuration Manual Download | Manualshive

Page: 11 / 54

background image

Channelized T1 Port Adapter Installation and Configuration 11

2CT1 Port Adapter Cables and Pinouts

Table 2

2CT1 Port LED Indications

2CT1 Port Adapter Cables and Pinouts

Two standard serial cables, null-modem and straight-through, for the 2CT1 port adapter are available
from Cisco Systems and other vendors. Both cables have a 15-pin, D-shell (DB-15) connector at the
router (VIP2 or Cisco 7200 series) end and at the network end. Figure 6 shows the 2CT1 interface
cable, connectors, and pinouts.

Following are the product numbers for the 2CT1 interface cables:

•

Null-modem cable—CAB-7KCT1NULL(=) or equivalent

•

Straight-through cable—CAB-7KCT1DB15(=) or equivalent

Figure 6

2CT1 Interface Cable

Table 3 lists connector pinouts for the 2CT1 null-modem cable, and Table 4 lists the connector
pinouts for the 2CT1 straight-through cable.

Port LED

Status

LB (loopback)

This green LED comes on when the port is in loopback mode
(line or local). The LED remains off during normal operation
of the port adapter.

LA (local alarm)

This green LED comes on when the incoming signal from a
remote source is out-of-frame (OOF), contains more than one
errored second (ES) signal in a ten-second sampling period, or
there is a loss of the incoming signal (LOS). The LED remains
off during normal operation of the port adapter.

RA (remote alarm)

This green LED comes on when the remote source’s incoming
signal is OOF, contains more than one ES in a ten-second
sampling period, or there is LOS. The LED remains off during
normal operation of the port adapter.

Pin 1

DB-15 connector

Pin 9

Pin 11

Pin 3

72-XXXX-01

MIP

H8665

DB-15 connector

«
...
9
10
11
12
13
...
»

Summary of Contents for PA-2CT1























































Reviews:

No comments

Related manuals for PA-2CT1

Brand: Qlogic Pages: 2

Brand: Aztech Pages: 2

Brand: Saramonic Pages: 2

Brand: Actron Pages: 2

Brand: Lindy Pages: 2

Brand: Avaya Pages: 2

802.11g PCI Card Wireless Adapter

Brand: 2Wire Pages: 17

Brand: LSILogik Pages: 2

Brand: Marshall Amplification Pages: 6

Brand: Gigabyte Pages: 39

Brand: Atheros Pages: 52

Pavilion zv5000 - Notebook PC

Brand: Compaq Pages: 2

Brand: Peltor Pages: 96

Brand: Parker Pages: 2

Brand: Schwaiger Pages: 2

Brand: Kinivo Pages: 8

Brand: innoXplore Pages: 3

Brand: Westinghouse Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands