Cisco ONS 15454 M6 Installation Manual Download Page 30 | Manualshive

Page: 30 / 164

background image

When mounting the ONS 15454 M6 in a frame with a nonconductive coating (such as paint, lacquer, or
enamel) either use the thread-forming screws provided with the ONS 15454 M6 ship kit, or remove the coating
from the threads to ensure electrical continuity.

Caution

In an ANSI rack, reversible mounting brackets (19-inch or 23-inch) are used to install the shelf. The mounting
brackets can be installed in the front or the middle position of the chassis.

Note

Procedure

Step 1

To mount the reversible brackets:

• For a 19-inch (482.6-mm) configuration, place the widest side of the mounting bracket flush against the

shelf (see

Figure 29: Mounting the Brackets on the ONS 15454 M6 shelf for a 19-inch (482.6-mm) ANSI

Configuration, on page 31

). The narrow side of the mounting bracket should be towards the front of the

shelf.

• For a 23-inch (584.2-mm) configuration, place the narrow side of the mounting bracket flush against the

shelf (see

Figure 30: Mounting the Brackets on the ONS 15454 M6 shelf for a 23-inch (584.2-mm) ANSI

Configuration, on page 31

). The widest side of the mounting bracket should be towards the front of the

shelf.

Step 2

Align the mounting bracket screw holes against the shelf screw holes.

Step 3

Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 4

Repeat steps 1 through 3 for the mounting bracket on the opposite side.

The following figure shows mounting the brackets for a 19-inch (482.6-mm) configuration.

Installing the ONS 15454 M6 Shelf

30

Installing the ONS 15454 M6 Shelf

DLP-G560 Mounting the Reversible Brackets on the ONS 15454 M6 Shelf for ANSI Rack Configuration

«
...
28
29
30
31
32
...
»

Summary of Contents for ONS 15454 M6





































































































































































Reviews:

No comments

Related manuals for ONS 15454 M6

Brand: Alcatel Pages: 140

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands