Cisco ONS 15454 M6 Installation Manual Download Page 140 | Manualshive

Page: 140 / 164

background image

• To configure the Catalyst 3560 using IOS commands for the ONS 15454 shelf as the node controller,

complete the

NTP-G298 Configure a Cisco Catalyst 2950 or Catalyst 3560 (Active and Standby) for a

ONS 15454 Multishelf Node

• To configure the Catalyst 3560 using IOS commands for the ONS 15454 M6 shelf as the node controller,

complete the

NTP-G298 Configure a Cisco Catalyst 2950 or Catalyst 3560 (Active and Standby) for a

ONS 15454 Multishelf Node

Stop. You have completed this procedure.

DLP-G682 Connect the ONS 15454 M6 as the Node Controller in a Mixed
Multishelf Configuration Using the Catalyst 3560

Use this procedure to connect the ONS 15454 M6 as the node controller and a
mix of ONS 15454 and ONS 15454 M6 as subtending shelves using a Catalyst
3560.

Purpose

• Two Cisco Catalyst 3560 switches must be installed in same rack as the node

controller shelf; see the Cisco Catalyst 3560 product documentation for
installation instructions.

• Cross-over (CAT-5) LAN cables (3, plus 2 for each subtending shelf)

Tools/Equipment

NTP-G15 Install the Common Control Cards

NTP-G313 Install and Configure the TNC, TNCE, TSC, or TSCE Card

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

The MSM (multishelf management) ports are present on the ECU module. The MSM ports located on the left
side of the ECU module correspond to the TNC/TNCE/TSC/TSCE card in Slot 1, and the MSM ports located
on the right side correspond to the TNC/TNCE/TSC/TSCE card in Slot 8. For more information about the
ECU module and MSM ports, see the

External Connection Units, on page 72

Note

Use the craft terminal port or the EMS port present on the ECU module to connect the ONS 15454 M6 node
controller to the LAN.

Note

Procedure

Step 1

Using a cross-over (CAT-5) LAN cable:

Installing the ONS 15454 M6 Shelf

140

Installing the ONS 15454 M6 Shelf

DLP-G682 Connect the ONS 15454 M6 as the Node Controller in a Mixed Multishelf Configuration Using the Catalyst 3560

«
...
138
139
140
141
142
...
»

Summary of Contents for ONS 15454 M6





































































































































































Reviews:

No comments

Related manuals for ONS 15454 M6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands