manualshive.com logo in svg

Cisco ONS 15454 M6, Installation Manual

The Cisco ONS 15454 M6 is a cutting-edge network transport platform designed for seamless connectivity. Ensure a hassle-free installation with our comprehensive and easy-to-follow Installation Manual. Download the manual for free from our website manualshive.com and unlock the full potential of this incredible product.

Share
Download
background image

Figure 1: Cisco ONS 15454 M6 Shelf Dimensions for a 19-inch ANSI Rack Configuration

Reversible Mounting Bracket

Use only the fastening hardware provided with the ONS 15454 M6 shelf to prevent loosening, deterioration,
and electromechanical corrosion of the hardware and joined material.

Caution

When mounting the ONS 15454 M6 shelf in a frame with a nonconductive coating (such as paint, lacquer,
or enamel) either use the thread-forming screws provided with the ONS 15454 M6 shipping kit, or remove
the coating from the threads to ensure electrical continuity.

Caution

The reversible mounting bracket is used to mount the shelf on a 19-inch or 23-inch (482.6 mm or 584.2 mm)
rack.

Mounting a Single Shelf

Mounting the ONS 15454 M6 shelf on a rack requires a minimum of 10.4-inches (265 mm) of vertical rack
space. To ensure that the mounting is secure, use two to three #12-24 mounting screws for each side of the
shelf. For an ANSI rack, the brackets can be mounted in the front or middle position.

Installing the ONS 15454 M6 Shelf

3

Installing the ONS 15454 M6 Shelf

Reversible Mounting Bracket

Summary of Contents for ONS 15454 M6





































































































































































Reviews:

No comments

Related manuals for ONS 15454 M6

Brands by name

Popular brands

Load more brands