Cisco ONS 15454 M6 Installation Manual Download Page 29

Page: 29 / 164

Figure 28: DC Power Module Installation—Rear Side of the ONS 15454 M6 Shelf

Step 2

Loosen the screw and move it to the right position (towards the DC silk-screen text).

Step 3

Tighten the screw again to a torque value of 4 in-lb (0.45 N-m).

Step 4

Return to your originating procedure (NTP).

DLP-G560 Mounting the Reversible Brackets on the ONS 15454 M6 Shelf for
ANSI Rack Configuration

This task installs the reversible mounting brackets on the ONS 15454 M6 shelf
for ANSI rack configuration.

Purpose

• #2 Phillips Dynamometric screwdriver
• Medium slot-head screwdriver
• Small slot-head screwdriver

Tools/Equipment

NTP-G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454
M6 Shelves

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Use only the fastening hardware provided with the ONS 15454 M6 to prevent loosening, deterioration, and
electromechanical corrosion of the hardware and joined material.

Caution

Installing the ONS 15454 M6 Shelf

DLP-G560 Mounting the Reversible Brackets on the ONS 15454 M6 Shelf for ANSI Rack Configuration

Summary of Contents for ONS 15454 M6





































































































































































Search results

Summary of Contents for ONS 15454 M6

Reviews:

Related manuals for ONS 15454 M6

Brands by name

Popular brands

Cisco ONS 15454 M6, Installation Manual

Search results

Summary of Contents for ONS 15454 M6

Reviews:

Related manuals for ONS 15454 M6

Brands by name

Popular brands