Cisco ONS 15454 M6 Installation Manual Download Page 138 | Manualshive

Page: 138 / 164

background image

Cross-over (CAT-5) LAN cables

Tools/Equipment

NTP-G313 Install and Configure the TNC, TNCE, TSC, or TSCE Card

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

The multishelf management (MSM) ports are present on the ECU module. The MSM ports located on the left
side of the ECU module correspond to the TNC/TNCE/TSC/TSCE card in Slot 1, and the MSM ports located
on the right side correspond to the TNC/TNCE/TSC/TSCE card in Slot 8. For more information about the
ECU module and MSM ports, see the

External Connection Units, on page 72

Note

Procedure

Step 1

Using a cross-over (CAT-5) LAN cable:

a) Plug one connector into the MSM port that corresponds to the TNC/TNCE/TSC/TSCE card in Slot 1 of

the ONS 15454 M6 shelf used as the node controller.

b) Plug the other connector into the MSM port that corresponds to the TNC/TNCE/TSC/TSCE card in Slot

1 of the ONS 15454 M6 shelf used as subtending shelf.

Step 2

Using a cross-over (CAT-5) LAN cable:

a) Plug one connector into the MSM port that corresponds to the TNC/TNCE/TSC/TSCE card in Slot 8 of

the ONS 15454 M6 shelf used as the node controller.

b) Plug the other connector into the MSM port that corresponds to the TNC/TNCE/TSC/TSCE card in Slot

8 of the ONS 15454 M6 shelf used as subtending shelf.

Step 3

Repeat Step 1 and Step 2 to connect the remaining two MSM ports of the ONS 15454 M6 shelf, used as the
node controller, to the subsequent subtending ONS 15454 M6 shelf assemblies.

The node controller can support up to three subtended shelves, while each of the subtended shelf
can support only two more SSCs.

Note

Step 4

To extend the number of SSCs, using a cross-over (CAT-5) LAN cable:

a) Plug one connector to any one of the remaining MSM ports of the ONS 15454 M6 SSCs in the first layer.
b) Plug the other connector to any one of the MSM ports of the ONS 15454 M6 SSCs in the next layer.
c) Repeat a and b to connect the remaining MSM ports of the ONS 15454 M6 in the first layer to the next

layer.

Stop. You have completed this procedure.

Installing the ONS 15454 M6 Shelf

138

Installing the ONS 15454 M6 Shelf

NTP-G308 Connect the ONS 15454 M6 Multishelf Node and the ONS 15454 M6 Subtending Shelves

«
...
136
137
138
139
140
...
»

Summary of Contents for ONS 15454 M6





































































































































































Reviews:

No comments

Related manuals for ONS 15454 M6

Brand: EXTREME SWITCHING Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands