Cisco ONS 15454 M6 Installation Manual Download Page 102 | Manualshive

Page: 102 / 164

background image

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than: 40A and between -40.5 VDC to -57.6 VDC.

Statement

1005

Warning

For nominal voltage of –60 VDC, the input voltage range is from -50 to -72 VDC.

Note

This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than: 10A-20A, 100-240 VAC~.

Statement 1005

Warning

A readily accessible two-poled disconnect device must be incorporated in the fixed wiring.

Statement

1022

Warning

This unit might have more than one power supply connection; all connections must be removed to
de-energize the unit.

Statement 1028

Warning

Always use the supplied ESD wristband when working with a powered ONS 15454 M6. For detailed instructions
on how to wear the ESD wristband, see the

Electrostatic Discharge and Grounding Guide for Cisco CPT and

Cisco ONS Platforms

.

Caution

Procedure

Step 1

Verify that the correct fuse and alarm panel is installed in the top mounting space:

• For a a DC power supply, the fuse rating must not exceed 40A.

• For an AC power supply, the fuse rating must not exceed 10A, 15A, or 20A. For North America, the

branch circuit protection must be rated 20A. The overcurrent/short circuit protection must be in accordance
with local and national electrical codes.

Step 2

Depending on the shelf and the power module installed, complete the necessary task:

•

DLP-G571 Connect Office Power (AC) to the ONS 15454 M6 Shelf, on page 103

•

DLP-G572 Connect Office Power (DC) to the ONS 15454 M6 Shelf (ANSI Only), on page 107

•

DLP-G573 Connect Office Power (DC) to the ONS 15454 M6 Shelf (ETSI Only), on page 111

Installing the ONS 15454 M6 Shelf

102

Installing the ONS 15454 M6 Shelf

NTP-G256 Install Power and Ground to the ONS 15454 M6 Shelf

«
...
100
101
102
103
104
...
»

Summary of Contents for ONS 15454 M6





































































































































































Reviews:

No comments

Related manuals for ONS 15454 M6

Brand: Isilon Systems Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands