Cisco NCS 2000 series Troubleshooting Manual Download Page 325 | Manualshive

Page: 325 / 602

background image

The MXP_2.5G_10E card has no LOS (TRUNK) option, because G.709 cannot be disabled on the card.

Note

The alarm is raised when the card port is not receiving input. An AIS is sent upstream.

The purpose of the LOS (TRUNK) alarm is to alert the user that no optical power is being received from the
fiber. A typical fault condition signalled by the LOS (TRUNK) alarm is a fiber cut. In this case, neither the
payload nor the overhead signals are being received.

With G.709 off, the alarm coming from the trunk is LOS (TRUNK) in accordance with SONET standards.

Note

In R7.01, when an LOS (TRUNK) alarm occurs on TXP and MXP trunks, G709/SONET/SDH TCAs are
suppressed.

Note

Clear the LOS (TRUNK) Alarm

Check the PMs of the TRUNK-RX port and verify that the received power is above the optics threshold.

SUMMARY STEPS

1.

Check that a proper threshold has been provisioned. (For procedures, refer to the Provision Transponder
and Muxponder Cards chapter in the Configuration guide.) If an incorrect threshold has been set, adjust
it to a value within the allowed limits. If the alarm condition does not clear, move to next step.

2.
3.

Using an optical test set, verify that a valid signal exists on the line and feeds the TRUNK-RX port.(For
specific procedures to use the test set equipment, consult the manufacturer.) Test the line as close to the
receiving card as possible. If the alarm condition does not clear, move to next step.

4.

Verify whether a bulk attenuator is specified in the Cisco TransportPlanner design. If so, verify that the
proper fixed attenuation value has been used.

5.
6.

Look for and troubleshoot any alarms reported by the DWDM cards belonging to the OCHNC circuit
whose destination is the faulty TXP/MXP. Possible alarms include: amplifier gain alarms (the

alarm, the

GAIN-HFAIL , on page 210

alarm, the

GAIN-LDEG , on page 211

alarm or

GAIN-LFAIL , on page 211

alarm); APC alarms (the

APC-CORR-SKIPPED , on page 119

alarm and

APC-OUT-OF-RANGE , on page 120

alarm), OR LOS-P alarms on the Add or Drop ports belonging to

the OCHNC circuit.

DETAILED STEPS

Step 1

Check that a proper threshold has been provisioned. (For procedures, refer to the Provision Transponder and Muxponder
Cards chapter in the Configuration guide.) If an incorrect threshold has been set, adjust it to a value within the allowed
limits. If the alarm condition does not clear, move to next step.

Step 2

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

279

Alarm Troubleshooting

Clear the LOS (TRUNK) Alarm

«
...
323
324
325
326
327
...
»

Summary of Contents for NCS 2000 series



























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NCS 2000 series

NetDefend DFL-260E

Brand: D-Link Pages: 328

ShareCenter Pulse DNS-320

Brand: D-Link Pages: 2

DFL-210 - NetDefend - Security Appliance

Brand: D-Link Pages: 19

Brand: D-Link Pages: 22

Brand: D-Link Pages: 4

Brand: Dahua Pages: 12

NetDefend DFL-1600

Brand: D-Link Pages: 23

IntelliJack NJ200

Brand: 3Com Pages: 4

Brand: H3C Pages: 16

Brand: H3C Pages: 24

Brand: Harman Kardon Pages: 66

Brand: IBM Pages: 32

Brand: Xinje Pages: 57

Brand: Paradyne Pages: 2

Brand: Paradyne Pages: 20

Brand: Paradyne Pages: 2

Brand: Zhone Pages: 2

RDX QuikStation 4

Brand: Tandberg Data Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands