manualshive.com logo in svg

Cisco NCS 2000 series, Troubleshooting Manual

The Cisco NCS 2000 series Troubleshooting Manual is an essential resource for users seeking to resolve technical issues with ease. Download this comprehensive manual for free from manualshive.com, providing step-by-step guidance and expert insights to keep your Cisco NCS 2000 series product running smoothly.

Share
Download
background image

Clear the RLS Condition

Step 1

To clear the RLS condition on

OPT-RAMP-C and OPT-RAMP-CE

cards, perform the following steps:

a) Disconnect the LINE-RX port cable.
b) Clean all the optical connectors from LINE RX to the customer fiber distribution panel through all the patch panels.

To do this, perform the task "NTP-G115 Clean Fiber Connectors" in the Hardware Installation Guide.

c) Reconnect the LINE-RX port cable. Wait five minutes for the Raman link restart procedure to be completed on

OPT-RAMP-C and OPT-RAMP-CE cards.

If the RLS condition does not clear, replace the optical cable connected to the LINE-RX port. Repeat Step 1b . If the RLS
condition persists, call the Cisco TAC (1 800 553-2447) to open a Return Material Authorization (RMA) case.

Step 2

To clear the RLS condition on

EDRA-1-xx, EDRA-2-xx

cards, perform the following steps:

a) Disconnect the LINE-RX port cable.
b) Clean all the optical connectors from LINE RX to the customer fiber distribution panel through all the patch panels.

To do this, perform the task "NTP-G115 Clean Fiber Connectors" in the Hardware Installation Guide.

c) Reconnect the LINE-RX port cable.

If the RLS condition does not clear, replace the optical cable connected to the LINE-RX port. Repeat Step 1b . If the RLS
condition persists, call the Cisco TAC (1 800 553-2447) to open a Return Material Authorization (RMA) case.

Step 3

To clear the RLS condition on

RAMAN-CTP

cards, perform the following steps:

a) Disconnect the LINE-RX port cable.
b) Clean all the optical connectors from LINE RX to the customer fiber distribution panel through all the patch panels.

To do this, perform the task "NTP-G115 Clean Fiber Connectors" in the Hardware Installation Guide.

c) Reconnect the LINE-RX port cable.
d) In CTC, click the RAMAN-CTP card view >

Maintenance

>

Config & Safety

tabs and click the

Manual Safety

Restart

button.

If the RLS condition does not clear, replace the optical cable connected to the LINE-RX port. Repeat Step1b. If the RLS
condition persists, call the Cisco TAC (1 800 553-2447) to open a Return Material Authorization (RMA) case.

Step 4

To clear the RLS condition on

RAMAN COP

cards, perform the following steps:

a) Disconnect the RAMAN-RX port cable on Raman CTP card.
b) Clean the high power patch-cord between RAMAN RX port on Raman CTP and RAMAN TX port on Raman COP

card.

c) Reconnect the patch-cord.
d) In CTC, click the RAMAN-CTP card view >

Maintenance

>

Config & Safety

tabs and click the

Manual Safety

Restart

button.

If the RLS condition does not clear, replace the optical cable connected to the LINE-RX port. Repeat Step1b. If the RLS
condition persists, call the Cisco TAC (1 800 553-2447) to open a Return Material Authorization (RMA) case.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

379

Alarm Troubleshooting

Clear the RLS Condition

Summary of Contents for NCS 2000 series



























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NCS 2000 series

D-Linke DHP-346AV Quick Installation Manual preview
DHP-346AV
Brand: D-Linke Pages: 32
D-Link DI-634M Quick Installation Manual preview
DI-634M
Brand: D-Link Pages: 12
Lauterbach C2000 Manual preview
C2000
Brand: Lauterbach Pages: 61
Hal Communications RS2100 Instruction Manual preview
RS2100
Brand: Hal Communications Pages: 25
CAME QBEMFSB2 User Manual preview
QBEMFSB2
Brand: CAME Pages: 19
Planet ADSL 2/2+ Router with USB Port ADE-3410v2 User Manual preview
ADSL 2/2+ Router with USB Port ADE-3410v2
Brand: Planet Pages: 62
bintec elmeg RM7000 Installation Manual preview
RM7000
Brand: bintec elmeg Pages: 33
Omega OMB-DAQBOARD-500 Series User Manual preview
OMB-DAQBOARD-500 Series
Brand: Omega Pages: 48
ZALMAN ZM80C-HP Manual preview
ZM80C-HP
Brand: ZALMAN Pages: 18
Allied Telesis AT-AR3050S Installation Manual preview
AT-AR3050S
Brand: Allied Telesis Pages: 80
Corsair H80i v2 Quick Start Manual preview
H80i v2
Brand: Corsair Pages: 12
Conel LR77 v2 SL User Manual preview
LR77 v2 SL
Brand: Conel Pages: 32
2N Telekomunikace ATEUS STARGATE User Manual preview
ATEUS STARGATE
Brand: 2N Telekomunikace Pages: 67
Telestar DIGIBIT R1 Operating Manual preview
DIGIBIT R1
Brand: Telestar Pages: 16
Belkin Home Base F5L049ea User Manual preview
Home Base F5L049ea
Brand: Belkin Pages: 59
MicroNet SP3362F User Manual preview
SP3362F
Brand: MicroNet Pages: 49
Homeworks HQP7-RF-2 Installation Instructions Manual preview
HQP7-RF-2
Brand: Homeworks Pages: 24
LevelOne FSW-0512 Specification Sheet preview
FSW-0512
Brand: LevelOne Pages: 2

Brands by name

Popular brands

Load more brands