Cisco NCS 2000 series Troubleshooting Manual Download Page 356 | Manualshive

Page: 356 / 602

background image

Logical Object: OTS

The NO-SHARED-CIPHERS alarm is raised when the certificates with different encryption cipher or algorithm
are provisioned on either the server or the client.

Clear the NO-SHARED-CIPHERS Alarm

Verify the same encryption cipher or algorithm is provisioned on both the server and the client.

If the alarm does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

NON-CISCO-PPM

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

Logical Object: PPM

The Non-Cisco PPM Inserted condition occurs when a PPM that is plugged into a card port fails the security
code check. The check fails when the PPM used is not a Cisco PPM.

Clear the NON-CISCO-PPM Condition

SUMMARY STEPS

1.

Obtain the correct Cisco PPM and replace the existing PPM with the new one.

DETAILED STEPS

Obtain the correct Cisco PPM and replace the existing PPM with the new one.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

NODE-FACTORY-MODE

Default Severity: Critical (CR)

Logical Object: NE

The Node Factory Mode alarm is raised when the database is not available due to the following:

• New installation.
• Reset NE to factory defaults.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

310

Alarm Troubleshooting

Clear the NO-SHARED-CIPHERS Alarm

«
...
354
355
356
357
358
...
»

Summary of Contents for NCS 2000 series



























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NCS 2000 series

Brand: A-Link Pages: 6

Brand: Palm Pages: 4

Brand: Ubiquiti Pages: 50

Brand: MiLAN Pages: 1

PacketShaper PS-S200

Brand: Symantec Pages: 2

Brand: EZCast Pro Pages: 4

Brand: ekwb Pages: 2

Brand: CopperOptics Pages: 12

Brand: Cypress Semiconductor Pages: 38

HHM Series HHM1521

Brand: TDK Pages: 2

Brand: E-Lins Pages: 10

Brand: MESA Electronic Pages: 27

Brand: Boser Pages: 82

OmniSwitch 6624

Brand: Alcatel Pages: 546

Brand: Altronix Pages: 8

Brand: Intel Pages: 11

Brand: Moxa Technologies Pages: 94

Brand: MikroTik Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands