Cisco NCS 2000 series Troubleshooting Manual Download Page 588 | Manualshive

Page: 588 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

Enter valid watermark values.

The watermark values are either out of range or
inconsistent.

EID-6157

Refer to the error message text.

The 1+1 protection group is not optimized.

EID-6179

Operation is requested on a failed or
missing equipment.

The equipment has failed or is missing.

EID-6196

You cannot change the attributes when
the port is in the specified
administrative state.

Attributes cannot be changed when the port
administrative state is {0}.

EID-6197

Refer to the warning message text.

This action will cause the node to reboot. When
provisioning in single-shelf mode, Shelf {0} of the node
that you connect to must be properly preprovisioned or
you will lose traffic. Use the LCD to return to
single-shelf mode. CTC cannot be used for this.
Changing from subtended shelf mode to single-shelf
mode could be traffic-affecting.

WID-6204

The user creates an ADM peer group
without interlink ports.

The interlink port is not provisioned.

EID-6205

The user creates an ADM peer group
involving an ADM card inserted in a
peer group.

The ADM peer group has already been created on the
peer card.

EID-6206

The selected ADM card is not
involved in an ADM peer group.

This card is not in the ADM peer group.

EID-6207

Refer to the error message text.

The payload is not OTU2.

EID-6208

During the creation of a side on node,
a side is already defined.

The side is already defined by the node.

EID-6209

The user requests an operation on a
side, but no side is selected.

No side was selected.

EID-6210

CTC could not delete the selected side
successfully.

The side was not deleted.

EID-6211

An operation on a port was not
performed because the port is
connected to a patchcord or a virtual
link.

One of the ports is connected to a patchcord or virtual
link.

EID-6212

During the creation of a side it is not
possible to associate the selected ports
to the new side.

It is not possible to associate the side to the two ports.

EID-6213

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

542

Error Messages

Error Messages Reference

«
...
586
587
588
589
590
...
»

Summary of Contents for NCS 2000 series



























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NCS 2000 series

Brand: H3C Pages: 33

S5500-SI Series

Brand: H3C Pages: 1217

Brand: 3Com Pages: 2443

Brand: H3C Pages: 3

Brand: H3C Pages: 4

Brand: Patton electronics Pages: 2

Brand: Patton electronics Pages: 86

Brand: National Instruments Pages: 26

Brand: National Instruments Pages: 85

Module SCXI-1503

Brand: National Instruments Pages: 79

Brand: Compaq Pages: 112

RouterBOARD SXT 5HnD

Brand: MikroTik Pages: 2

Brand: UNA AUTOMATION Pages: 20

Brand: Maipu Pages: 80

COMMWARE ECHO 5G

Brand: pivotal Pages: 2

IP-Logic ZIG-IPPRO-RX

Brand: Zigen Pages: 4

Brand: IBM Pages: 44

Brand: Ezquest Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands