Cisco ME 3400 Series Software Configuration Manual Download Page 741 | Manualshive

Page: 741 / 1138

background image

35-15

Cisco ME 3400 Ethernet Access Switch Software Configuration Guide

OL-9639-07

Chapter 35 Configuring IP Unicast Routing

Configuring IP Addressing

To restore the default IP broadcast address, use the

no ip broadcast-address

interface configuration

command.

Flooding IP Broadcasts

You can allow IP broadcasts to be flooded throughout your internetwork in a controlled fashion by using
the database created by the bridging STP. Using this feature also prevents loops. To support this
capability, bridging must be configured on each interface that is to participate in the flooding. If bridging
is not configured on an interface, the interface can receive broadcasts but it never forwards the broadcasts
it receives, and the router never uses that interface to send broadcasts received on a different interface.

Packets that are forwarded to a single network address using the IP helper-address mechanism can be
flooded. Only one copy of the packet is sent on each network segment.

To be considered for flooding, packets must meet these criteria. (Note that these are the same conditions
used to consider packet forwarding using IP helper addresses.)

•

The packet must be a MAC-level broadcast.

•

The packet must be an IP-level broadcast.

•

The packet must be a TFTP, DNS, Time, NetBIOS, ND, or BOOTP packet, or a UDP specified by
the

ip forward-protocol udp

global configuration command.

•

The time-to-live (TTL) value of the packet must be at least two.

A flooded UDP datagram is given the destination address specified with the

ip broadcast-address

interface configuration command on the output interface. The destination address can be set to any
address so it might change as the datagram propagates through the network. The source address is never
changed. The TTL value is decremented.

When a flooded UDP datagram is sent out an interface (and the destination address possibly changed),
the datagram is handed to the normal IP output routines and is, therefore, subject to access lists, if they
are present on the output interface.

Beginning in privileged EXEC mode, follow these steps to use the bridging spanning-tree database to
flood UDP datagrams:

Use the

no ip forward-protocol spanning-tree

global configuration command to disable the flooding

of IP broadcasts.

In the switch, the majority of packets are forwarded in hardware; most packets do not go through the
switch CPU. For those packets that do go to the CPU, you can speed up spanning tree-based UDP
flooding by a factor of about four to five times by using turbo-flooding. This feature is supported over
Ethernet interfaces configured for ARP encapsulation.

Command

Purpose

Step 1

configure terminal

Enter global configuration mode.

Step 2

ip forward-protocol spanning-tree

Use the bridging spanning-tree database to flood UDP datagrams.

Step 3

end

Return to privileged EXEC mode.

Step 4

show running-config

Verify your entry.

Step 5

copy running-config startup-config

(Optional) Save your entry in the configuration file.

«
...
739
740
741
742
743
...
»

Summary of Contents for ME 3400 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ME 3400 Series

Brand: Garland Pages: 4

Brand: Juniper Pages: 825

IMACS Network Device

Brand: Zhone Pages: 114

Brand: QNAP Pages: 54

Brand: TP-Link Pages: 87

Brand: Caton Pages: 18

BROADCAST POLLING FRAD BPF-14 BU

Brand: DCB Pages: 28

OmniStor 4900F Series

Brand: Rackable Systems Pages: 196

Brand: ATTO Technology Pages: 2

Brand: NetComm Pages: 34

JetNet 5720G-8P Series

Brand: Korenix Pages: 52

Brand: StarTech.com Pages: 16

EonStor GS 3000 Series

Brand: Infortrend Pages: 134

ROUTE FINDER RFIPSC-1

Brand: Multitech Pages: 54

Brand: King Pigeon Pages: 8

Brand: Westermo Pages: 22

Brand: ProCurve Pages: 406

Junxion Box JB-110b

Brand: Junxion Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands