Cisco ASR 1001-X Hardware Installation Manual Download Page 79

Page: 79 / 152

C H A P T E R

Upgrading the ROMMON and CPLD

This chapter describes the procedures to upgrade the ROMMON on the Cisco ASR 1001-X Router.

This chapter contains the following sections:

•

Upgrading the ROMMON, page 71

•

Compatible ROMMON Releases, page 75

•

Resolved Caveats, page 75

•

Hardware the Require a CPLD Upgrade, page 75

•

Checking Hardware and Software Compatibility, page 77

Upgrading the ROMMON

The ROMMON must be upgraded on the Cisco ASR 1001-X Router if the system message on the router
indicates that the ROMMON requires an upgrade, or when a Cisco technical support representative suggests
a ROMMON upgrade.

Compatibility Requirements

For information about the compatibility between the ROMMON releases and the Cisco ASR 1001-X
Router, see the

“

ROMMON Release Requirements

”

section in the

Cisco ASR 1000 Series Aggregation

Services Routers Release Notes

Note

To upgrade the ROMMON image, you must have access to the privileged EXEC mode prompt or the diagnostic
mode prompt on the router.

Checking the Current ROMMON Version

If you are unsure whether a ROMMON upgrade is required, follow the instructions provided in this section.

Cisco ASR 1001-X Router Hardware Installation Guide

Summary of Contents for ASR 1001-X
























































































































































Search results

Summary of Contents for ASR 1001-X

Reviews:

Cisco ASR 1001-X, Hardware Installation Manual, Page: 79 / 152

Search results

Summary of Contents for ASR 1001-X

Reviews: