manualshive.com logo in svg

Cisco ASR 1001-X, Hardware Installation Manual, Page: 105 / 152

Share
Download
Cisco ASR 1001-X Hardware Installation Manual Download Page 105

DETAILED STEPS

Step 1

Turn off the circuit breaker from the power source.

Step 2

At the rear of the router, ensure that the power switch is in the Standby position.

It is not required to place the power switch in the Standby position if you want to hot-swap a single power
supply.

Note

Step 3

Unscrew the two terminal block wire connectors (negative and positive) on the unit. See the below figure.

Step 4

Press the retaining latch towards the pull handle, grasp the handle with one hand, and pull the power supply out of the
slot while supporting the weight of the power supply with the other hand. See the below figure.

Figure 13: Removing DC Power Supply

Retaining latch

1

This completes the procedure for removing a DC power supply from the Cisco ASR 1001-X Router.

Installing DC Input Power on the Cisco ASR 1001-X Router

Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1003

Danger

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030

Danger

This section describes how to install the DC power supply input power leads to the Cisco ASR 1001-X Router
DC input power supply. Before you begin, read these important notices:

•

The color coding of the DC input power supply leads depends on the color coding of the DC power
source at your site. Ensure that the lead color coding you choose for the DC input power supply matches

Cisco ASR 1001-X Router Hardware Installation Guide    

97

Removing and Replacing FRUs from the Cisco ASR 1001-X Router

Installing DC Input Power on the Cisco ASR 1001-X Router

Summary of Contents for ASR 1001-X

























































































































































Reviews:

No comments