Cisco ASR 1001-X Hardware Installation Manual Download Page 10

Page: 10 / 152

•

Stratum 3E network clocking per GR-1244-CORE, using 1588, 10 GE, GE, SPA, or Network Interface
Module (NIM) interfaces as timing sources.

•

Six built-in 1 GE SFP-only interfaces (do not support SFP+), and two built-in 10 GE SFP+ interfaces
(support only 10-GE rate) that support SyncE.

•

One half-height SPA bay.

•

Software redundancy using Dual IOS, similar to all the other nonhardware redundant routers from the
Cisco ASR 1000 Series Aggregation Services Router family.

•

LED indicators for Ethernet and console status, as well as visual system state indications.

•

Command-line interface (CLI), alarm, network management, logging, statistics aggregation, and on-board
failure logging (OBFL).

•

Environmental chassis management.

•

10 MB ternary content-addressable memory (TCAM).

•

Up to 20 Gbps sustained forwarding data traffic through the chassis.

•

One Network Interface Module (NIM) bay.

The NIM bay supports the T1/E1 NIMs and the Solid State Device (SSD) NIM assembly and drive.

Note

•

Field-replaceable units (FRU) with online insertion and removal (OIR).

Cisco ASR 1001-X Overall Chassis Front View

The following figure shows the front of the Cisco ASR 1001-X Router.

Figure 1: Cisco ASR 1001-X Router Front View

Shared port adapter slot

NIM slots

USB port 0

CON

—

One mini eUSB

por

USB port 1

PWR

—

Power LED

Cisco ASR 1001-X Router Hardware Installation Guide

Cisco ASR 1001-X Router Overview

Cisco ASR 1001-X Overall Chassis Front View

Summary of Contents for ASR 1001-X
























































































































































Search results

Summary of Contents for ASR 1001-X

Reviews:

Cisco ASR 1001-X, Hardware Installation Manual, Page: 10 / 152

Search results

Summary of Contents for ASR 1001-X

Reviews: