Cisco ASR 1001-X Hardware Installation Manual Download Page 99

Page: 99 / 152

C H A P T E R

Removing and Replacing FRUs from the Cisco
ASR 1001-X Router

This chapter describes procedures for removing and replacing field-replaceable units (FRUs) from Cisco
ASR 1001-X Routers.

This chapter contains the following sections:

•

Removing and Replacing the Cisco ASR 1001-X Router Power Supplies, page 91

•

Removing and Replacing Cisco ASR 1001-X Router USB Flash Memory Stick or Secure Token, page

101

•

Removing and Replacing the Cisco ASR 1001-X Router DIMM, page 102

•

Removing and Replacing a Cisco ASR 1001-X Router SPA , page 108

•

Removing and Replacing a NIM on the Cisco ASR 1001-X Router, page 111

•

Removing and Replacing an SSD from the NIM-SSD Module, page 113

•

Repacking the Router, page 118

Removing and Replacing the Cisco ASR 1001-X Router Power
Supplies

The following sections describes the procedures for removing and replacing the Cisco ASR 1001-X Router
power supplies.

The Cisco ASR 1001-X Router has redundant power supplies that can be hot-swapped.

Note

The covers are an integral part of the safety design of the product. Do not operate the unit without the
covers installed. Statement 1077

Danger

Cisco ASR 1001-X Router Hardware Installation Guide

Summary of Contents for ASR 1001-X
























































































































































Search results

Summary of Contents for ASR 1001-X

Reviews:

Cisco ASR 1001-X, Hardware Installation Manual, Page: 99 / 152

Search results

Summary of Contents for ASR 1001-X

Reviews: