manualshive.com logo in svg

Cisco ASR 1001-X, Hardware Installation Manual, Page: 80 / 152

Share
Download
Cisco ASR 1001-X Hardware Installation Manual Download Page 80

Run the

show rom-monitor

command or the

show platform

command to display the version of ROMMON

running on your router. If the output shows that the release to which you plan to upgrade is already installed,
you need not upgrade the ROMMON.

For a single form-factor platform such as the Cisco ASR 1001-X Router, all of the following commands
display the same output:

•

show rom-monitor 0

•

show rom-monitor F0

•

show rom-monitor FP

•

show rom-monitor R0

•

show rom-monitor RP

In the following example, the output of the

show rom-monitor

command indicates that an upgrade to Release

15.4(2r)S is not required:

Router#

show rom-monitor 0

System Bootstrap, Version 15.4(2r)S, RELEASE SOFTWARE (fc1)
Copyright (c) 1994-2014

by cisco Systems, Inc.

Upgrading the ROMMON for the Cisco ASR 1001-X Router

Use this procedure to upgrade the ROMMON for the Cisco ASR 1001-X Router:

SUMMARY STEPS

1.

(Optional) Run the

show platform

command or the

show rom-monitor slot

command to see the current

release number of ROMMON on the hardware.

2.

If the ROMMON image has not been copied onto the router, copy the PKG file that is made available as
part of this ROMMON release onto the bootflash: or usb[0-1]: file system using the

copy source-location

destination-location

command. For example, if you are upgrading to Release 15.4(2r)S, copy the

asr1000-rommon.154-2r.S.pkg file.

3.

Run the

dir file-system

command to verify that the ROMMON file is copied into the specified directory.

4.

Run the

upgrade rom-monitor filename location all

command to begin the ROMMON image upgrade,

where

location

is the path to the ROMMON file.

5.

Messages pertaining to the upgrade are displayed on the console. After the display of these messages stops
and the router prompt is available, run the

reload

command to reload the router.

6.

If autoboot has not been enabled by using the

config-register 0x2102

command, run the

boot

filesystem:/file-location

command at the ROMMON prompt to boot the Cisco IOS XE image, where

filesystem:/file-location

is the path to the consolidated package file. The ROMMON upgrade is not

permanent for any piece of hardware until the Cisco IOS XE image is booted.

7.

Run the

enable

command at the user prompt to enter the privileged EXEC mode after the boot is complete.

8.

Run the

show platform

command or the

show rom-monitor slot

command to verify whether the

ROMMON has been upgraded.

   Cisco ASR 1001-X Router Hardware Installation Guide

72

Upgrading the ROMMON and CPLD

Upgrading the ROMMON for the Cisco ASR 1001-X Router

Summary of Contents for ASR 1001-X

























































































































































Reviews:

No comments