Cisco ASR 1001-X Hardware Installation Manual Download Page 146

Page: 146 / 152

SPARE

Normally Closed
(NC)

Normally Open
(NO)

Common
(CM)

Description

Signal

—

Critical Visual
Alarm

CRTVA

—

Major Visual
Alarm

MAJVA

—

Minor Visual
Alarm

MINVA

10, 11, 12, 13,
23, 24, 25

—

SPARE

—

unused

pin reserved for
future use

SPARE

Cisco ASR 1001-X Router Specifications

Table 54: Cisco ASR 1001-X Router Specifications , on page 138

lists the Cisco ASR 1001-X Router physical

specifications.

The Cisco ASR 1001-X Router has the route processor, embedded services processor, and

SIP

integrated

in the chassis.

Note

Table 54: Cisco ASR 1001-X Router Specifications

Specification

Description

Height

—

1.71 in. (43.43 mm)

Width

—

17.3 in. (439.42 mm)

Depth

—

22.50 in. (571.5 mm) including card handles,

cable-management brackets, and power supply
handles)

Dimensions (H x W x D)

25 lb fully loaded

Weight

0° to 40° C

Nominal operating temperature

0° to 50° C

Short-term operating temperature

10 to 90% relative humidity

Nominal operating humidity

5 to 90%

Short-term operating humidity

–

20° to +70° C

Storage temperature

Cisco ASR 1001-X Router Hardware Installation Guide

138

Cisco ASR 1001-X Router Specifications

Summary of Contents for ASR 1001-X
























































































































































Search results

Summary of Contents for ASR 1001-X

Reviews:

Cisco ASR 1001-X, Hardware Installation Manual, Page: 146 / 152

Search results

Summary of Contents for ASR 1001-X

Reviews: