Cisco ASR 1001-X Hardware Installation Manual Download Page 120

Page: 120 / 152

•

Number 2 Phillips or a 3/16-inch flat-blade screwdriver

•

NIM

•

Cables

•

Your own ESD-prevention equipment or the disposable grounding wrist strap included with all upgrade
kits, FRUs, and spares

•

Antistatic mat or surface, or static shielding bag

If you need additional equipment, contact a Cisco service representative for ordering information.

For information about electrostatic discharge prevention, see the

Electrostatic Discharge Prevention, on

page 108

Note

Removing a NIM

To remove a NIM, follow these steps.

SUMMARY STEPS

Attach an ESD wrist strap between you and an unpainted chassis surface.

Stop the NIM so that there is no traffic running through the NIM when it is removed, using the following
steps:

Disconnect all the cables from the NIM.

Unscrew the captive installation screws on either side of the NIM.

Grasp the handles using both hands and pull out the NIM.

DETAILED STEPS

Step 1

Attach an ESD wrist strap between you and an unpainted chassis surface.

Step 2

Stop the NIM so that there is no traffic running through the NIM when it is removed, using the following steps:

Removing a NIM while traffic is flowing through the ports may cause system disruption.

Caution

a) At the router# prompt, enter

hw-module subslot 0/2 stop

and press

Enter

b) At the router# prompt, enter

end

and press

Enter

Step 3

Disconnect all the cables from the NIM.

Step 4

Unscrew the captive installation screws on either side of the NIM.

Step 5

Grasp the handles using both hands and pull out the NIM.
You have completed the NIM removal procedure.

Cisco ASR 1001-X Router Hardware Installation Guide

112

Removing and Replacing FRUs from the Cisco ASR 1001-X Router

Removing a NIM

Summary of Contents for ASR 1001-X
























































































































































Search results

Summary of Contents for ASR 1001-X

Reviews:

Cisco ASR 1001-X, Hardware Installation Manual, Page: 120 / 152

Search results

Summary of Contents for ASR 1001-X

Reviews: