manualshive.com logo in svg

Cisco ASR 1001-X, Hardware Installation Manual, Page: 26 / 152

Share
Download
Cisco ASR 1001-X Hardware Installation Manual Download Page 26

Cisco ASR 1001-X Power Supply Fans

The fans in the power supply module of the Cisco ASR 1001-X Router are used for cooling the power supply
module itself while system-level cooling is provided by four fans within the chassis. The power supplies do
not depend on the system-level fans for cooling. Fan failure is determined by fan-rotation sensors.

The fans in the power supply modules will run as soon as the power supply is plugged in, even if the
Standby switch is in the Standby position.

Note

Cisco ASR 1001-X Router AC Power Supply

The Cisco ASR 1001-X Router has two AC power supplies in the rear of the chassis. The input receptacle is
an IEC60320 C14 type of filtered AC inlet. The current rating on the connector is 10 A. The following figure
shows the Cisco ASR 1001-X Router AC power supply.

Figure 7: Cisco ASR 1001-X Router AC Power Supply

AC power connector

3

Handle

1

Retaining latch

4

FAIL and OK LEDs

2

Cisco ASR 1001-X Router DC Power Supply

The Cisco ASR 1001-X Router DC input connector is a two-wire connector with connection polarity from
left to right (when facing the unit) of negative (

–

) positive (+).

   Cisco ASR 1001-X Router Hardware Installation Guide

18

Cisco ASR 1001-X Router Supported Hardware Components

Cisco ASR 1001-X Power Supply Fans

Summary of Contents for ASR 1001-X

























































































































































Reviews:

No comments