manualshive.com logo in svg

Cisco ASR 1001-X, Hardware Installation Manual, Page: 119 / 152

Share
Download
Cisco ASR 1001-X Hardware Installation Manual Download Page 119

DETAILED STEPS

Step 1

To insert a SPA, locate the guide rails that hold the SPA in place. They are at the top left and top right of the SPA slot
and are recessed about an inch.

Step 2

Carefully slide the SPA all the way in using both hands until the SPA is firmly seated in the SPA interface connector.
When fully seated, the SPA might be slightly behind the faceplate.

Step 3

After the SPA is properly seated, fasten the SPA in place with the captive installation screws on either side of the SPA.

Ensure that you fasten the captive installation screws to provide appropriate connectivity.

Note

Step 4

Restart the SPA using the following steps:

a) At the router# prompt, enter

hw-module subslot 0/1 start

and press

Enter.

b) At the router# prompt, enter

end

and press

Enter

.

Step 5

Use the

show platform

command to verify whether the status of subslot 0/1 is OK.

show platform Command

Example:

Router#

show platform

Chassis type: ASR1001-X
Slot

Type

State

Insert time (ago)

--------- ------------------- --------------------- -----------------
0

ASR1001-X

ok

00:34:05

0/0

BUILT-IN-2T+6X1GE

ok

00:33:14

0/1

SPA-4XT-SERIAL

ok

00:33:14

0/2

NIM-SSD

ok

00:33:11

R0

ASR1001-X

ok

00:34:05

R0/0

ok, active

00:34:05

R0/1

ok, standby

00:32:47

F0

ASR1001-X

ok, active

00:34:05

P0

ASR1001X-PWR-AC

ps, fail

00:33:44

P1

ASR1001X-PWR-AC

ok

00:33:42

P2

ASR1001-X-FANTRAY

ok

00:33:47

Slot

CPLD Version

Firmware Version

--------- ------------------- ---------------------------------------
0

14041015

15.4(2r)S

R0

14041015

15.4(2r)S

F0

14041015

15.4(2r)S

You have completed the Cisco ASR 1001-X Router SPA replacement procedure.

Removing and Replacing a NIM on the Cisco ASR 1001-X Router

The OIR feature allows you to install and replace a NIM while the router is operating. You do not have to
shut down the system

’

s power although you should not run traffic through the NIM while it is being removed.

OIR is a method that is seamless to end users on the network, and maintains all routing information and
preserves sessions.

As you disengage the NIM from the router, OIR shuts down all the active interfaces in the NIM.

Note

We recommend that you have the following tools and parts readily available for installing a NIM:

Cisco ASR 1001-X Router Hardware Installation Guide    

111

Removing and Replacing FRUs from the Cisco ASR 1001-X Router

Removing and Replacing a NIM on the Cisco ASR 1001-X Router

Summary of Contents for ASR 1001-X

























































































































































Reviews:

No comments