Cisco ASR 1001-X Hardware Installation Manual Download Page 64

Page: 64 / 152

Configuring the Enable and Enable Secret Passwords

To provide an additional layer of security, particularly for passwords that cross the network or are stored on
a TFTP server, you can use either the

enable password

command or

enable secret

command. Both commands

accomplish the same thing

—

they allow you to establish an encrypted password that users must enter to access

privileged EXEC (enable) mode.

We recommend that you use the

enable secret

command because it uses an improved encryption algorithm.

For more information, see the

“

Configuring Passwords and Privileges

”

chapter in the

Cisco IOS Security

Configuration Guide

. Also see the

Cisco IOS Password Encryption Facts

tech note and the

Improving Security

on Cisco Routers

tech note.

If you configure the

enable secret

command, it takes precedence over the

enable password

command;

the two commands cannot be in effect simultaneously.

Note

SUMMARY STEPS

enable

configure terminal

enable secret password

end

enable

end

DETAILED STEPS

Purpose

Command or Action

Enables privileged EXEC mode.

enable

Step 1

Example:

Router> enable

•

Enter your password if prompted.

Enters global configuration mode.

configure terminal

Example:

Router# configure terminal

Step 2

Specifies an additional layer of security over the

enable

password

command.

enable secret password

Example:

Router(config)# enable secret

greentree

Step 3

Cisco ASR 1001-X Router Hardware Installation Guide

Cisco ASR 1001-X Router Power Up and Initial Configuration

Using the Cisco IOS-XE CLI--Manual Configuration

Summary of Contents for ASR 1001-X
























































































































































Search results

Summary of Contents for ASR 1001-X

Reviews:

Cisco ASR 1001-X, Hardware Installation Manual, Page: 64 / 152

Search results

Summary of Contents for ASR 1001-X

Reviews: