background image

 

 

 

28 

              Configuration       c6 

Level 3 access

 

Supply air fan 

 

K = ----- 

 

 

 

Return air fan 

 

K = ----- 

 

 

 

 

 

Supply air fan

: K coefficient values for the Supply air fan 

Return air fan

: K coefficient values for the Return air fan 

 
 

2.4

 

Adjustment parameters menu 

 

                                               lg 

Level 1 access

 

 

 

Language          ------------ 

Controller language selection (French) 

 

 

 

 

 

 

 

 

 

 

 

                                              t0 

Level 1 access

 

Setting 

of the clock 

 

 

 

Time         -- :-- 

Clock time correction value 

Date         --/--/-- 

Clock date correction value 

 

 

 

 

 

               Supply air                p1 

Level 2 access

 

Cooling DB                        00.0 

Deadband value for Supply air temperature control in cooling mode 

CLG band                      0005.0 

Proportional band for Supply air temperature control in cooling mode 

T I 0150s                  T D 0000s 

Integral time and derivative time for Supply air temperature control in cooling mode 

 

 

Heating DB                       00.0 

Deadband value for Supply air temperature control in heating mode 

HTG band                      0005.0 

Proportional band for Supply air temperature control in heating mode 

T I 0150s                  T D 0000s 

Integral time and derivative time for Supply air temperature control in heating mode 

 

               Return air                p2 

Level 2 access

 

                Differential 

Value for the Return or Ambient air temperature control differentials 

Cooling                         Heating 

In cooling mode 

 

 

In heating mode 

  0.0                                     0.0 

 

 

 

 

 

 

 

 

 

 

                                             p3 

Level 2 access

 

Fan management 

 

   -------- 

 

 

 

 

 

 

 

Free Cooling                 ---- 

 

Fire                               ---- 

 

Fan management

Without, Flow rate (

constant flows and independent setpoints)

 or Pressure (

Constant supply air duct pressure 

and identical fan speed values)

 

Free Cooling

Without, With

 

Fire

Without, With

 

 

 

Summary of Contents for AirCompact Control






































































Reviews: