Chino IR-HA Series Instructions Manual Download Page 38

Page: 38 / 52

INST.No.INE-567-P1CE

-30-

9. Zero/Span Adjustment Mode

◆

By measuring scale lower limit (zero side) and higher limit (span side) with your black body furnace and

input black body furnace temperature, this function performs zero/span adjustment.

･

Start zero/span adjustment by push and holding



key,

ENT

key, and

MEASURE

key at the same time

while power OFF.

Status flow is shown on the right.
For each setting and selection, refer to the individual
sections.

Remark

Caution

･

Be sure to prepare a black body furnace and a reference radiation

thermometer.

If those instruments can not be provided, do not perform zero/span
adjustment.

･

Check that emissivity (ratio) is 1.000 then perform the adjustment.

If no key operation has done for 30sec., power

supply is turned OFF automatically.

(IR-HAI/IR-HAQ)

Flow Chart

Initialize Zero/Span

InGaAs Zero Adjustment

Perform Zero/Span

Adjustment

InGaAs Span Adjustment

Si Zero Adjustment

Si Span Adjustment

2-Color Zero Adjustment

2-Color Span Adjustment

SEL

(IR-HAI/IR-HAQ)

(IR-HAS/IR-HAQ)

(IR-HAQ)

Summary of Contents for IR-HA Series





















































Search results

Summary of Contents for IR-HA Series

Reviews:

Related manuals for IR-HA Series

Brands by name

Popular brands

Chino IR-HA Series, Instructions Manual

Search results

Summary of Contents for IR-HA Series

Reviews:

Related manuals for IR-HA Series

Brands by name

Popular brands