Chino IR-HA Series Instructions Manual Download Page 17 | Manualshive

Page: 17 / 52

background image

INST.No.INE-567-P1CE

-9-

FILTER

ON

4.5 Cautions on Measurement

◆

To protect the eyes, make sure to turn "ON (attenuation side)" beam attenuation filter

switch if measuring 1500°C or more.

Caution

Warning

Warning

！

FILTER

ON

[Enlarged view]

Never sight the objective lens of the thermometer to the sunlight directly for protecting your eyes

and a detecting element.

・

For the measurement of an object exceeding 1500°C, make sure to turn the beam attenuation

filter switch "ON (attenuation side)" for protecting your eyes.

・

When you feel glare on the measurement of an objects lower than 1500°C, turn the beam

attenuation filter switch "ON (attenuation side)".

・

Light path

Be careful not to introduce water drops, dust particles, smoke, steam, or other foreign

substances into the light path between the object measured and the objective lens of the
thermometer.

・

Interference causing high indication

Be careful not to apply the direct sunlight, light of an incandescent lamp, flame or other

thermal radiation to the object measured and the objective lens of the thermometer.

To the attenuation side!

«
...
15
16
17
18
19
...
»

Summary of Contents for IR-HA Series





















































Reviews:

No comments

Related manuals for IR-HA Series

Brand: Bacharach Pages: 19

SourceMeter 2400

Brand: Keithley Pages: 594

System SourceMeter 2601B

Brand: Keithley Pages: 864

Brand: Labgear Pages: 8

SourceMeter 2600B Series

Brand: Keithley Pages: 897

Brand: Veeder-Root Pages: 39

Brand: Veeder-Root Pages: 98

Brand: VECTECH Pages: 9

Brand: Major tech Pages: 16

Brand: Zoetis Pages: 2

SoundTrack LxT N/Forcer

Brand: Larson Davis Pages: 12

Brand: Mark-10 Pages: 26

Brand: Aqua Lung Pages: 24

Brand: Toro Pages: 60

Brand: A&D Pages: 2

Brand: Omega Pages: 16

Brand: A&D Pages: 10

Brand: LaserLiner Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands