Chino IR-HA Series Instructions Manual Download Page 49

Page: 49 / 52

INST.No.INE-567-P1CE

-41-

14. Start-up Option

14.1 Start-up Option

The following operation modes are available by the key combinations at the start up.

Key Operation

Mode

Remarks

Push

MEASURE

key only

Standard measuring or
Continuous measuring

Measurement

with

the

same

measuring

mode

the

last

start-up

Push



key while pushing

MEASURE

key

Standard measuring

Push



key while pushing

MEASURE

key

Continuous measuring

" under main marker "CONT"

lights

Push



key,

ENT

key, and

MEASURE

key at the same time

Zero/Span

adjustment

mode

If it is start-up by only

MEASURE

key at next start-up, it will be
standard measuring or continuous
measuring.

14.2 Table of Display

The displays indicated on the external LCD are classified as three types.

Mode

Outline

Measuring mode

Push

MEASURE

key to perform measurement.

Emissivity setting and automatic calculation of emissivity is available at
holding standard/continuous measuring display.

Setting mode

Displays and sets measurement parameter.
By pushing and holding

SEL

key in standard/continuous measuring mode or

memory input mode, it shifts to setting mode.
In any setting mode, push and hold

SEL

key or not operating any key for about

one minute, it becomes measuring mode or memory input mode.

Memory input mode

Memory number setting, displaying memory data, and saving memory data is
available.
By pushing

MEMORY

key at standard/continuous measuring mode, it becomes

memory input mode and lights "MEM".
By pushing

MEMORY

key again, it returns to standard/continuous measuring

mode.

Zero/Span adjustment
mode

Performs zero/span adjustment using black body furnace.
If no key operation has done for 30sec., power supply is turned OFF
automatically.

Summary of Contents for IR-HA Series





















































Search results

Summary of Contents for IR-HA Series

Reviews:

Related manuals for IR-HA Series

Brands by name

Popular brands

Chino IR-HA Series, Instructions Manual

Search results

Summary of Contents for IR-HA Series

Reviews:

Related manuals for IR-HA Series

Brands by name

Popular brands