Chino IR-HA Series Instructions Manual Download Page 15 | Manualshive

Page: 15 / 52

background image

INST.No.INE-567-P1CE

-7-

4.2 About SD Card

4.3 Inserting SD Card

◆

Open SD card connector cover and insert SD card.

Reference

Caution

Caution

Warning

When setting SD card,
this side up and insert
the card.

SD card

Operation key

SD card connector cover

SD card slot

If the card is inserted up side down, it may

cause the failure.

Be sure to remove and insert SD card when the power supply is turned OFF.

！

・

Operation under SD card other than our recommended item is not guaranteed.

・

Maximum capacity is 2GB, so 2GB or more can not be used.

・

If SD card is formatted (initialized) by PC etc., the card may not work properly. Refer to "6.13 SD

Card Data Initialization" for format and follow the procedure.

・

Remove and insert SD card when the power supply is turned OFF.

・

Do not turn OFF the power supply of the radiation thermometer while it is accessing SD card.

・

If battery voltage is low, it can not access to the SD card. Change the battery.

・

If memory function is used when the SD card is not inserted, "Er51" is displayed.

・

If the SD card is protected by write protection, "LoCK" is displayed when saving the data.

To remove the SD card, push the SD card lightly and pull out the card when the tip of
the card comes out from the "SD card slot".

«
...
13
14
15
16
17
...
»

Summary of Contents for IR-HA Series





















































Reviews:

No comments

Related manuals for IR-HA Series

Brand: Samson Pages: 4

Brand: Xylem Pages: 24

Brand: Eaton Pages: 87

Brand: Eaton Pages: 16

Brand: OBDPROG Pages: 8

Brand: Omega Pages: 170

Solicap M FTI55

Brand: Endress+Hauser Pages: 92

Brand: Seben Pages: 16

Brand: RADWAG Pages: 176

Brand: PANCONTROL Pages: 157

Brand: ACCRETECH Pages: 104

Brand: General Pages: 12

EUROGRAND EG2080

Brand: Behringer Pages: 34

Brand: Ratek Pages: 24

Brand: Amptec Research Pages: 19

Brand: S&T Pages: 23

Brand: Hanna Instruments Pages: 12

Brand: Vaisala Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands