Chino IR-HA Series Instructions Manual Download Page 31

Page: 31 / 52

INST.No.INE-567-P1CE

-23-

7.1 Standard Measuring Mode

1) Sight through the viewfinder and match the center circle

of the targeting circle to the center of object measured.

2) Turn ON the power by holding down

MEASURE

key.

3) Start measurement by pushing

MEASURE

key. Status

marker "MEAS" lights and temperature is displayed on the
main display.
Measurement continues while holding down on the key.

4) When

MEASURE

key is released, status marker "MEAS"

turned OFF and status marker "HOLD" lights,
measurement is paused and holds measured value.

5) By pushing

SEL

key, the sub marker switches "MAX"

(highest temperature)

→

"AVE" (average temperature)

→

"TC" (thermocouple temperature)

→

"MIN" (lowest

temperature) and each values can be displayed.

Remark

If the measured value is +21°C or more of measuring

range higher limit, "oFL" is displayed, and -20°C or
less of measuring range lower limit, "uFL" is
displayed.

Push MEASURE key

CONT

MEM

PEAK

MEAS

MAX

℃

[Pause]

Sub marker

Status marker

[Standard measuring mode
display]

CONT

MEM

PEAK

MAX

HOLD

Summary of Contents for IR-HA Series





















































Search results

Summary of Contents for IR-HA Series

Reviews:

Related manuals for IR-HA Series

Brands by name

Popular brands

Chino IR-HA Series, Instructions Manual

Search results

Summary of Contents for IR-HA Series

Reviews:

Related manuals for IR-HA Series

Brands by name

Popular brands