manualshive.com logo in svg

Chattanooga Group Intelect Legend XT, Service Manual

Share
Download
Chattanooga Group Intelect Legend XT Service Manual Download Page 64

59

Vectra Genisys®/Intelect Legend XT®/ Intelect® Vet Therapy Systems

6 REMOVAL/REPLACEMENT

A. Tools & Equipment Required

#1 Phillips Screwdriver
Flat Blade Screwdriver
Needle Nose Pliers

The following procedures apply to all Channel 3/4 
Electrotherapy, NiMH Battery, and Laser Modules 
(Vectra Genisys and Intelect Vet) that mount to the 
base of a Therapy System.

B. Module Installation

Disconnect Therapy System from the 
power source.
Remove the Rear Panel and disconnect the 
Power Cord from the System. 

See Figure 

6.1.

Place system on a level working surface.
Remove the Front Access Panel and 
disconnect all existing cables and Lead 
Wires. 

See Figure 6.2.

Using a #1 Phillips Screwdriver, remove the 
screw securing the Lanyard to the Front 
Access Panel. 

See Figure 6.3.

NOTE:

When turning over Therapy System onto 
its face, place a clean, soft cloth under the 
lens to prevent scratching or lens damage.
If the system is equipped with an sEMG 
Module, leave it in place to maintain sEMG 
functions for Channels 1 and 2. The sEMG 
Module will not interfere with installation of 
a Module to the Therapy System.

Turn system over, remove the label 
covering the Ribbon Cable and unroll 
Ribbon Cable. 

See Figure 6.4.

1.
2.
3.

1.

2.

3.
4.

5.

6.

FIGURE 6.1

FIGURE 6.2

REMOVE FRONT ACCESS 

PANEL AND DISCONNECT 

ALL CABLES

FIGURE 6.3

REAR PANEL

DISCONNECT

POWER CORD

REMOVE

LANYARD

FIGURE 6.4

REMOVE

LABEL

Be careful not to disconnect the Ribbon Cable from 
the Vectra Genisys, Intelect Legend XT and Intelect 
Vet Therapy Systems.

RIBBON 

CABLE

LEAVE SEMG 

IN PLACE

6.1 CHANNEL 3/4 ELECTROTHERAPY, NIMH  
 

BATTERY, AND LASER MODULE  

 

 

INSTALLATION AND REMOVAL

DISCONNECT THE SYSTEM FROM THE POWER 
SOURCE (OUTLET OR REMOVE BATTERY MODULE IF 
INSTALLED) BEFORE ATTEMPTING ANY MAINTENANCE, 
INSTALLATION, REMOVAL, OR REPLACEMENT 
PROCEDURES TO PREVENT ELECTRICAL SHOCK AND 
POSSIBLE DAMAGE TO SYSTEM.

Summary of Contents for Intelect Legend XT



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands