manualshive.com logo in svg

Chattanooga Group Intelect Legend XT, Service Manual

Share
Download
Chattanooga Group Intelect Legend XT Service Manual Download Page 14

9

Vectra Genisys®/Intelect Legend XT®/ Intelect® Vet Therapy Systems

3 NOMENCLATURE

6

8

10

9

7

 

Screen Contrast Control (Not functional on Color 

 Systems)

 

System Power On/Off Switch

 

Technical Maintenance Port

 

Main Power Cord

 

Rear Access Panel

 

Two Channel Electrotherapy System

 

User Interface (Screen and Buttons)

 

Front Access Panel

 

Patient Data Card and sEMG Data Card access 

 port

1.

2.
3.
4.
5.
6.
7.
8.
9.

 

Multimedia Card (MMC) access port

 

Front Access Panel Lanyard- When reinstalling 

 the Front Access Panel, make certain the Lanyard 
 does not become kinked

 

Channel 1/2 Operator Remote Control Connector

 

Patient Interrupt Switch Connector

 

Channel 1 Lead Wire Connector

 

Channel 2 Lead Wire Connector

 

Microcurrent Probe Connector

 

Therapy System to Module Ribbon Cable

 (not shown)

10.
11.

12.
13.
14.
15.
16.
17.

17

3.1 VECTRA GENISYS, INTELECT LEGEND XT AND INTELECT VET THERAPY SYSTEMS (CONTINUED)

C. Vectra Genisys, Intelect Legend XT and Intelect Vet Electrotherapy Systems

The nomenclature graphics below, 

Figure

 

3.3

, 

indicate the general locations of the exterior  
components of the Two Channel Vectra Genisys, 
Intelect Legend XT or the Intelect Vet Two 
Channel Electrotherapy Systems.

Know the components and their functions 
before performing any operation of or service 
to the Vectra Genisys, Intelect Legend XT or 
the Intelect Vet Two Channel Electrotherapy 
Systems.

3

4

5

12

13

14

15

16

2

1

11

FIGURE 3.3

Summary of Contents for Intelect Legend XT



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands