manualshive.com logo in svg

Chattanooga Group Intelect Legend XT, Service Manual

Share
Download
Chattanooga Group Intelect Legend XT Service Manual Download Page 16

11

Vectra Genisys®/Intelect Legend XT®/ Intelect® Vet Therapy Systems

3 NOMENCLATURE

The nomenclature graphic below, 

Figure 3.5

, 

indicates the general locations of the exterior 
components of the Vectra Genisys, Intelect 
Legend XT and Intelect Vet Systems NiMH 
Battery Module.

Know the components and their functions 
before performing any operation of or service 
to the Vectra Genisys, Intelect Legend XT and 
Intelect Vet Therapy Systems NiMH Battery 
Module.

3.1 VECTRA GENISYS, INTELECT LEGEND XT AND INTELECT VET THERAPY SYSTEMS (CONTINUED)

E.  Vectra Genisys, Intelect Legend XT and Intelect Vet NiMH Battery Module

1

2

3

4

6

5

1. 

NiMH Battery Module

2.

  Extended Front Access Panel

3.

  Module to System Mounting Holes

4.

  Module to System Feet Alignment Indents

5.

  Power Cord Routing Port

6.

  Module to System Connector

NOTE:

The NiMH Battery Module is not operable unless it 
is properly connected to an Vectra Genisys, Intelect 
Legend XT, or Intelect Vet Therapy System.

FIGURE 3.5

Summary of Contents for Intelect Legend XT



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands