manualshive.com logo in svg

Chattanooga Group Intelect Legend XT, Service Manual

Share
Download
Chattanooga Group Intelect Legend XT Service Manual Download Page 23

18

Vectra Genisys®/Intelect Legend XT®/ Intelect® Vet Therapy Systems

4 SPECIFICATIONS

The specifications found in this section provide 
physical details of the Vectra Genisys, Intelect 
Legend XT and Intelect Vet Therapy Systems. This 
section also provides waveform specifications to 
aid in troubleshooting.

Refer to this section when performing 
troubleshooting, replacement, and repair of a 
Vectra Genisys, Intelect Legend XT and Intelect Vet 
Therapy System, Modules, and Accessories.

Dimensions
 Height

      Cart Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33.75 in (85.7 cm)

      With System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42.50 in (108 cm) 

      With System and Module  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.25 in (112.4 cm) 

 Width

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17 in (43.2 cm) 

Depth

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16.25 in (41.3 cm)

Power (Combination and Electrotherapy Systems)

  Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  100 - 240 V - 175 VA, 50/60 Hz

  Output (Internal Power Supply) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+24, 7.3 A

  Electrical Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CLASS I

  Mode of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous

Electrical Type

    Ultrasound (Combination Systems Only) and Laser Module (Vectra Genisys and Intelect Vet Only) . . . . TYPE B

    Electrotherapy, sEMG and Channel 3/4 Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TYPE BF

HEIGHT

CA

R

T ONL

Y

HEIGHT

WITH

 SY

STEM

 &

 SY

STEM

 WITH

 MODULE

WIDTH

DEPTH

4.1 VECTRA GENISYS, INTELECT LEGEND XT AND INTELECT VET THERAPY SYSTEMS

A. Therapy Systems Physical Specifications

FIGURE 4.1

Summary of Contents for Intelect Legend XT



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands