manualshive.com logo in svg

Chattanooga Group Intelect Legend XT, Service Manual

Share
Download
Chattanooga Group Intelect Legend XT Service Manual Download Page 62

57

Vectra Genisys®/Intelect Legend XT®/ Intelect® Vet Therapy Systems

5 TROUBLESHOOTING

The following checks for the NiMH Battery Module are 
to check for possible damage to the Battery Cells and 
proper connections within the module and module to 
System connection.

A. Tools and Equipment Required

#1 Phillips Screwdriver
Flat Blade Screwdriver

B. NiMH Battery Module Check Procedures

NOTE:

If it is suspected that the NiMH Battery cells 
may be damaged or leaking, perform 

steps 8 

through 13

 prior to any other tests or checks.

With the NiMH Battery Module properly 
installed onto the System, connect 
System Mains Power Cord to an approved 
electrical outlet.
Turn system On and view the Home 
Screen. The Charge Level and Battery 
Charging icons should appear in the 
lower left corner of the Home Screen. 

See 

Figure 5.36.
NOTE:

If Battery Module is fully charged, the 
Battery Charging Icon will not be visible 
and the Charge Level Icon will be fully 
black. If battery is fully charged, perform 

steps 4 through 7

 below then perform 

step 3

.

Allow battery to charge until it can be 
verified that it is charging by viewing the 
Charge Level icon until the level indicator 
fills more of the Charge Level icon.
Set up the Ultrasound Test as described in 

5.16

. Set Duty Cycle to 100%. Set Display 

to Watts, rotate Therapy Intensity knob 
until 10.0 Watts is visible, set Treatment 
Time to 60 minutes.
Disconnect System Mains Power Cord 
from wall power outlet.
With Ultrasound Applicator Sound Head 
submerged in the Power Meter degassed 
water, press start.
View the Charge Level Icon until it reduces 
the fill area of the icon. This verifies proper 
discharging of the battery module.
Turn System Off and remove the NiMH 
Battery Module from the System. Refer 
to the proper Removal & Replacement 
section for instructions.
Using the #1 Phillips Screwdriver, remove 
the two retaining screws in the top of the 
NiMH Battery Module. 

See Figure 5.37.

1.
2.

1.

2.

3.

4.

5.

6.

7.

8.

9.

FIGURE 5.37

FIGURE 5.36

5.20 NIMH BATTERY MODULE CHECKS

Summary of Contents for Intelect Legend XT



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands